Sony CDX-G1200U, Руководство по обслуживанию

Страница: 12 / 40

CDX-G1200U/G1201U/G1202U/G1280UM
12
Subwoofer Easy Connection
You can use a subwoofer without a power
amplifier when it is connected to a rear
speaker cord.
Notes
• Preparation of the rear speaker cords is required
(Argentine models only).
• Use a subwoofer with an impedance of 4 Ω to 8 Ω,
and with adequate power handling capacities to
avoid damage.
Memory hold connection
When the yellow power supply lead is
connected, power will always be supplied to
the memory circuit even when the ignition
switch is turned off.
Speaker connection
• Before connecting the speakers, turn the
unit off.
• Use speakers with an impedance of 4 Ω to
8 Ω, and with adequate power handling
capacities to avoid damage.
Make sure your car’s auxiliary power
connector, and match the connections of
cords correctly depending on the car.
Common connection
When the positions of the red and
yellow leads are inverted
When the car without ACC position
After matching the connections and
switching power supply leads correctly,
connect the unit to the car’s power supply. If
you have any questions and problems
connecting your unit that are not covered in
this manual, consult the car dealer.
1
To enable the wired remote control,
set [STR CONTROL] in [SET STEERING]
to [PRESET] (page 10).
Power connection diagram
(Argentine models only)
Front speaker
Subwoofer
Auxiliary power connector
12
continuous power
supply
Yellow
15 switched power supply Red
12 switched power supply Yellow
15
continuous power
supply
Red
Using the wired remote control
Red Red
Yellow Yellow
Red Red
Yellow Yellow
Red
Red
Yellow
Yellow
Installation
Before installing the unit, remove the
protection collar
ͨ
and the bracket
ʓ
from
the unit.
1
Pinch both edges of the protection
collar
ͨ
, then pull it out.
2
Insert both release keys
ͧ
until they
click, and pull down the bracket
ʓ
,
then pull up the unit to separate.
Removing the protection collar
and the bracket
ͨ
ʓ
†
ͧ
Face the hook inwards.
• Before installing, make sure the catches on
both sides of the bracket
ʓ
are bent
inwards 2 mm ( 3 /
32
in).
• For Japanese cars, see “Mounting the unit
in a Japanese car” (page 25).
1
Position the bracket
ʓ
inside the
dashboard, then bend the claws
outward for a tight fit.
2
Mount the unit onto the bracket
ʓ
,
then attach the protection collar
ͨ
.
Notes
• If the catches are straight or bent outwards, the
unit will not be installed securely and may spring
out.
• Make sure the 4 catches on the protection collar
ͨ
are properly engaged in the slots of the unit.
Mounting the unit in the
dashboard
ʓ
182 mm (7 1 /
4
in)
53 mm (2 1 /
8
in)
Catch
ʓ
ͨ
ͩ
ͪ
Mounting the unit in a Japanese car
You may not be able to install this unit in
some makes of Japanese cars. In such a
case, consult your Sony dealer.
TOYOTA
NISSAN
Note
To prevent malfunction, install only with the
supplied screws
ͫ
.
ͫ
to dashboard/center console
Existing parts supplied
with your car
ͫ
Bracket
Bracket
ͫ
to dashboard/center console
Existing parts supplied
with your car
ͫ
Bracket
Bracket
When replacing the fuse,
be sure to use one
matching the amperage
rating stated on the
original fuse. If the fuse
blows, check the power
connection and replace the
fuse. If the fuse blows again after
replacement, there may be an internal
malfunction. In such a case, consult your
nearest Sony dealer.
Fuse replacement
Fuse (10 A)
.