11
For details, see “<CNS SETTINGS>” (page 44).
COM ERROR (red):
Indicates a communications error with
the video camera, CCU, or external control device (such as
an RCP-3000/1000 series Remote Control Panel).
FAN STOP (red):
Indicates the internal fan has stopped.
h
POWER switch and indicator
Turns the system power supply on/off to the unit, video
camera, and RCP-3000/1000 series Remote Control Panel or
other device connected to the REMOTE connector. Switch to
“
?
” to turn the power on, and switch to “
a
” to turn the power off.
The indicator lights up when power is turned on.
i
Optical signal condition indicators
Displays the communications link optical signal level condition
between the video camera, CCU, and the unit.
CAM
T
BPU:
Signal level from the unit to the video camera
CAM
t
BPU:
Signal level from the video camera to the unit
BPU
T
CCU:
Signal level from the CCU to the unit
BPU
t
CCU:
Signal level from the unit to the CCU
Indicates the receive signal status according to the following
indicators.
Two green indicators (right):
Receive signal condition is very
good.
One green indicator (2nd from right):
Receive signal
condition is OK.
One yellow indicator (2nd from left):
Receive signal level is
low.
One red indicator (left):
Receive signal level is extremely low.
j
Assignable buttons
You can assign functions to these buttons from the BPU menu.
k
Menu lock switch
Locks the menu control block on the front panel.
Rear Panel
a
REMOTE connector (round type, 8-pin)
Connects to an RCP-3000/1000 series Remote Control Panel
or MSU-1000 Master Setup Unit using a CCA-5 connection
cable. Remote control signals are transmitted and received via
this connector. It also supplies power when connected to an
RCP-3000/1000 series Remote Control Panel.
When connected to a CCU, do not connect anything to this
connector.
b
REFERENCE IN/OUT (reference sync signal)
connectors
• IN connector (BNC type) (left)
Inputs an external HD tri-level sync signal or SD reference
sync signal (black burst signal).
The type of reference signal is detected automatically and can
be checked in the setup menu.
When connected to a CCU, do not connect anything to this
connector.
• OUT connector (BNC type) (right)
When a reference sync signal is input on the IN connector or
the unit is turned off, the signal input on the IN connector is
output as-is (loop through). Otherwise, this connector outputs
an SD composite sync signal or a HD tri-level signal from the
internal sync signal generator (HD tri-level signal set by factory
default).
Available only when used as a camera extension unit.
c
(LAN) connector (RJ-45 8-pin)
Connects to a LAN. Connect to a LAN hub (10BASE-
T/100Base-TX) using a LAN cable (shielded type, category 5
or higher).
d
SDI1 and SDI2 (return video input) connectors (BNC
type)
Connects to 2-system, independent, 3G/HD-SDI return video
signal inputs. The SDI1/SDI2 selection is made using the
return switch on the video camera. The SDI2 connector
becomes the HD prompter input connector by enabling HD
PROMPTER on the <RETURN> page in the
CONFIGURATION menu.
Available only when used as a camera extension unit.
e
CAMERA connector (optical fiber connector)
Connects to a video camera using an optical fiber cable. All
video camera signals (power supply, control signals, video
signal, audio signal, etc.) can be transmitted and received via
a single optical fiber cable.
f
CCU (camera control unit) connector (optical fiber
connector)
Connects to a camera control unit using an optical fiber cable.
All video camera signals (power supply, control signals, video
signal, audio signal, etc.) can be transmitted and received via
a single optical fiber cable. In an extension mode connection,
it can also supply power to the camera by connecting an
HDCE-200 Camera Extension Adaptor.
A communications error may occur if there is any dust or other
matter on the surface of the optical fiber cable connector.
Always attach the connector cap when not in use.
g
-
AC IN (AC power supply) connector
Connects to the AC power supply using the specified power
supply cord. The power supply cord can be attached to the unit
using the optional plug holder.
S
LOT2
CCU
CAMERA
S
DI OUT 1
S
DI OUT 2
S
LOT4
HD
S
DI OUT
S
LOT
3
3
G/HD
S
DI OUT
S
LOT1
S
DI OUT 1
S
DI OUT 2
S
DI OUT
3
S
DI OUT 4
S
DI OUT
3
S
DI OUT 4
S
DI OUT 5
S
DI OUT 6
S
DI OUT 7
S
DI OUT
8
IN
OUT
REFERENCE
REMOTE
S
DI1
S
DI2
Note
Note
Note
