Sony Ericsson K700c Скачать руководство пользователя

Страница: 36 / 37

Working Instruction, Mechanical

3/00021-1/FEA 209 544/83 A

Company Internal



Sony Ericsson Mobile Communications AB

36(37)

4 Label

Tools

•

Hot air flow solder station

•

Blunt pair of tweezers

•

Zebra printer and computer

Instruction

This instruction should be used when you are intending to exchange an old label or assemble
a new one.

NOTE!
Notice the position of the label before removal.
Only one label is allowed on the frame.

1. Read the old label and/or write the information into the Labelmake program.

2. Heat up the label with a hot air flow solder station, if needed.

3. Carefully remove the label, make sure that all residues are gone. If necessary clean the

surface with Isopropyl alcohol. Do not scratch the frame.

4. Check that the right label format is loaded in the Zebra printer.

5. Write a new label by using the program Labelmake. Check that the printing is ok.

6. Take the new label and place it onto the frame according to

Fig 1.

Make sure that the

label is placed in the right position.

Fig 1.

Содержание K700c






































Результаты поиска

Содержание K700c

Отзывы:

Похожие инструкции для K700c

Бренды по названию

Популярные бренды

Sony Ericsson K700c, Руководство по эксплуатации, механическое

Результаты поиска

Содержание K700c

Отзывы:

Похожие инструкции для K700c

Бренды по названию

Популярные бренды