background image

INTRODUCTION

2

SAFETY INFORMATION

For your safety, and to ensure optimum performance, please thoroughly review the information in this 
manual before using the product. In particular, please pay attention to the following:

1.

  Place the amplifier on a solid, level surface such as a desk or table, and do NOT block the ventilation 

holes as this could result in damage to the amplifier.

2.

  Keep liquids and sprays away from the amplifier at all times!

3.

  Do not attempt to insert anything into the ventilation holes at any time, especially when the amplifier 

is on!

4.

  Keep out of the reach of children at all times.

5.

  This product has been designed to conform to European standard EN 50332 on maximum volume 

level, however, permanent hearing damage may still occur if you listen at a very high level for long 
periods. Please protect your hearing by exercising some caution with the volume control, especially 
when doing extended listening.

6

  This product MUST be connected to a grounded mains outlet!

7.

  There are NO user serviceable parts inside, and, due to the high voltages needed for operation, we 

strongly advise against opening the amplifier unit for any reason.

8.

  If any of the cables show signs of wear or damage, please do NOT use the system until they have 

been replaced.

LIABILITY WAIVER

The Sonoma Model One Electrostatic Headphone System has been designed for home use only. 
Sonoma Acoustics Inc. will not accept liability for any damage or injury arising from improper use/
misuse of this product.

Содержание M1





































Отзывы: