Sonny's WRAP AROUND Скачать руководство пользователя страница 4

Страница: 4 / 36

This document is confidential and proprietary to SONNY’S and cannot be used,

SonnysDirect.com

disclosed or duplicated without prior written consent. Content, prices and availability subject to change without notice

Wrap Around-RevB iv

Rev. 1.0

General Safety Precautions - Cont.

When working on any equipment that is higher than your shoulders, always use a fiberglass ladder that is in

good condition.

Do not attempt to repair or adjust any pressurized liquid or pneumatic part, hose, pipe or fitting while that

equipment is in operation.

Electrical connections and repairs must be performed by a Licensed Electrician Only.

Emergency “STOP” buttons must be well marked and their location and proper use reviewed with all per-

sonnel. Any activated “STOP” button must be reset only by the person who activated it. Clear the wash

tunnel of any people, ladders, hoses, tools and other loose items before restarting the equipment. An audible

device must sound to warn people that the equipment is starting.

Do not operate any piece of equipment that requires safety covers with those covers removed or improperly

installed. Do not operate any piece of equipment if any component of that piece is suspected to be defective

or malfunctioning.

Store all cleaning and washing solutions and oils in a well-ventilated area. Clean up fluid spills immediately

to prevent hazardous safety conditions. Be certain to follow all safety procedures on SDS Sheets for each

chemical product used.

All hydraulic and electric systems in the wash tunnel equipped with a torque relief or overload should be

checked and set at the minimum amount that will allow for proper functionality under normal washing

conditions.

No unauthorized people should ever be permitted in the wash tunnel or near the equipment at any time.

aution

When a piece of equipment must be in operation during inspection or maintenance, one

qualified technician must stay at the power disconnect switch while another qualified

technician performs the inspection or maintenance.

Содержание WRAP AROUND





































Результаты поиска

Содержание WRAP AROUND

Отзывы:

Бренды по названию

Популярные бренды

Sonny's WRAP AROUND, Руководство пользователя

Результаты поиска

Содержание WRAP AROUND

Отзывы:

Бренды по названию

Популярные бренды