manualshive.com logo in svg

Sonny's WRAP AROUND, Руководство пользователя

Поделиться
Скачать
Sonny's WRAP AROUND Скачать руководство пользователя страница 30

This document is confidential and proprietary to SONNY’S and cannot be used, 

SonnysDirect.com 

disclosed or duplicated without prior written consent. Content, prices and availability subject to change without notice

Wrap Around-RevB 26 

Rev. 1.0

8.  Preventive Maintenance

C

aution

 

FOR THE FIRST MONTH OF OPERATION CHECK ALL FITTINGS FOR 

TIGHTNESS EACH WEEK. PERFORM THIS INSPECTION TO THE SCHEDULE 

SHOWN BELOW AFTER THE FIRST MONTH OF OPERATION.

C

aution

 

Overgreasing your bearings will cause the seals to break. If grease is coming out from the 

top of the bearings, the seals are shot and you will need to replace your bearings soon.

Frequency

Check/Action

Daily

Check all hydraulic, air and chemical lines and fittings for leaks. Repair, or replace, as needed.
Check both brush units for proper operation and retract operation, listening for any unusual 

noises from the equipment.
Inspect brush cloth for cuts, grease, or oil. Clean or replace any cloth panels if any of these con-

ditions are found.
Check for proper chemical solution delivery.

Weekly

Grease the brush shaft four bolt flange bearings. Do not allow grease to come in contact with 

brush cloth.
Apply lithium grease to the cylinder rod. Work the rod in and out of the cylinder and wipe any 

excess grease of the rod.

Monthly

Inspecting all hardware and fittings for tightness.
Grease the brush hanger pillow block bearings. Do not allow grease to come in contact with 

brush cloth.
Inspect soap solution spray nozzles for wear. Replace as necessary.
Inspect the shocks by removing the air lines off the air cylinder and manually retracting the 

brush. The two brushes should return to the rest position (middle of the tunnel) with no air 

pressure and no pitch to the bearings. 
Thoroughly clean the equipment and framework.

Semi- 

Annually

Carefully inspect brush equipment cloth for wear and damage. Replace as necessary.

 

Содержание WRAP AROUND





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды