background image

 

Seite 

9

 von 

12

 

KIOTO_Installation_manual_2021                                                         © KIOTO Photovoltaics GmbH, Solarstraße 1, 9300 Sankt Veit/Glan - Österreich  06/2021

 

 

Commissioning of the photovoltaic power plant 

Before initiation of the generator, please check all components (observe the installation instructions of other 
components), the electrical connection and all plugs, that they are connected correctly and ensure that the 
connection is tight.

 

 

Solar generators with a direct current voltage from more than 50V must be installed/initiated 
by qualified persons!

 

The open circuit voltage of every serial connection should be checked after initiation. Follow the rule: Result 
of the measurement = sum of the open circuit voltages of the single modules. Consider the actual time, sun 
irradiation, shadowing and other factors while measuring the open circuit voltage, otherwise the result of the 
sum and the single results could deviate considerably. 

Maintenance 

  Soiling on the module surface can lead to a reduction in performance. 

  Clean the modules as required and soiled with plenty of water and a soft cloth or sponge without 

any detergent. Do not use high pressure cleaners! 

  If other additives or devices like aggressive chemicals, scrubbing agents, sharp blades or steel 

wool are used the guarantee and product warranty will be invalid! Never wipe off or scrape off 
pollution in a dry state of the module surface. 

  An additional application of water / dirt resistant coatings can affect the efficiency of the modules 

and also the yield, in a negative way. 

  Check the module wiring and the single module plugs to ensure they are clean, corrosion free, 

mechanically ok and tight in regular intervals. 

ATTENTION: Never disconnect the plugs under load!

 

  Free the modules, if necessary, from high snow loads. 

  Check the substructure in regular intervals for their tightness. 

  Never try to open or repair parts of the module or of the junction box on your own. 

  All other trouble shootings, repairing and maintenance works must be done by qualified, skilled 

staff/persons. 

 

 

 

 

 

For further information relating to warranties etc. please read through the GENERAL TERMS 
AND CONDITIONS of KIOTO Photovoltaics GmbH. 

 

Содержание KIOTO SOLAR Glas-60 framed Series













Отзывы: