SONIX SN8P2754 Скачать руководство пользователя страница 24

Страница: 24 / 157

SN8P275X Series

8-bit micro-controller build-in 12-bit ADC

SONiX TECHNOLOGY CO., LTD

Page 24

Version 0.7

2.1.2 CODE OPTION TABLE

Code Option

Content

Function Description

Low cost RC for external high clock oscillator and XOUT becomes to
Fcpu frequency output pin.

12M X’tal

High speed crystal /resonator (e.g. 12MHz) for external high clock
oscillator.

4M X’tal

Standard crystal /resonator (e.g. 4M) for external high clock oscillator.

IHRC_16M

High speed internal 16MHz RC. XIN/XOUT become to P3.2/P3.1
bi-direction I/O pins.

IHRC_RTC

High speed internal 16MHz RC with 0.5sec RTC. XIN/XOUT become to
P3.2/P3.1 bit-direction I/O pins.

High_Clk

32K X’tal

Low frequency, power saving crystal (e.g. 32.768KHz) for external high
clock oscillator.

Always_On

Watchdog timer is always on enable even in power down and green
mode.

Enable

Enable watchdog timer. Watchdog timer stops in power down mode.

Watchdog is running in green mode.

Watch_Dog

Disable Disable

Watchdog

function.

Fhosc/1

Instruction cycle is oscillator clock.
Notice: In Fosc/1, Noise Filter must be disabled.

Fhosc/2

Instruction cycle is 2 oscillator clocks.
Notice: In Fosc/1, Noise Filter must be disabled.

Fhosc/4

Instruction cycle is 4 oscillator clocks.

Fhosc/8

Instruction cycle is 8 oscillator clocks.

Fhosc/16

Instruction cycle is 16 oscillator clocks.

Fhosc/32

Instruction cycle is 32 oscillator clocks.

Fhosc/64

Instruction cycle is 64 oscillator clocks.

Fcpu

Fhosc/128 Instruction cycle is 128 oscillator clocks.

Enable

Enable ROM code Security function.

Security

Disable

Disable ROM code Security function.

Enable Enable

Noise

Filter.

Noise_Filter

Disable Disable

Noise

Filter.

P3.3

Enable P3.3 input only without pull-up resister.

Reset_Pin

Reset

Enable External reset PIN.

No Disable

External reset de-bounce time.

External Reset

Length

128 * ILRC

Enable

External reset de-bounce time.

Note:

In high noisy environment, enable “Noise Filter” and set Watch_Dog as “Always_On”

is strongly recommended.

Fcpu code option is only available for High Clock. Fcpu of slow mode is Flosc/4.

In external RC mode, the Noise_Filter is enabled by assembler.

If watchdog enable, watchdog timer is still counting in green mode.

Содержание SN8P2754






























































































































































Результаты поиска

Содержание SN8P2754

Отзывы:

Похожие инструкции для SN8P2754

Бренды по названию

Популярные бренды

SONIX SN8P2754, Руководство пользователя

Результаты поиска

Содержание SN8P2754

Отзывы:

Похожие инструкции для SN8P2754

Бренды по названию

Популярные бренды