SONIX SN8P26L38 Скачать руководство пользователя страница 8

Страница: 8 / 136

SN8P26L38

8-Bit Micro-Controller

SONiX TECHNOLOGY CO., LTD

Page 8

Version 1.5

PRODUCT OVERVIEW

1.1

FEATURES



Memory configuration



Two 8-bit Timer/Counter

OTP ROM size: 8K * 16 bits.

T0: Basic timer.

RAM size: 880 * 8 bits.

TC1: Auto-reload timer/counter.



8 levels stack buffer



One RTC timer (T0).



One channels PWM output.



I/O pin configuration



One channels buzzer output.

Bi-directional: P0, P1, P2, P3, P4, P5



One channel IR output (duty/cycle programmable

Programmable open-drain: P1.0, P1.1, P5.0~P5.2,

PWM, TC0).

P3.2, P3.3.



On chip watchdog timer and clock source is internal

Wakeup:P0, P1 level change trigger.

low clock RC type (about 10KHz @3V).

P1 wake-up function controlled by P1W.

Pull-up resisters: P0, P1, P2, P3, P4, P5



One channel SIO interface.

External interrupt input: P0.0, P0.1



One channel UART interface.

External Interrupt trigger edge:

P0.0 controlled by PEDGE register



Four system clocks

External high clock: RC type up to 8 MHz



3-Level LVD.

External high clock: Crystal type up to 8 MHz

Reset system and power monitor.

Internal high clock: RC type 8MHz.

Internal low clock: RC type 10KHz(3V).



2-ch analog comparators with internal selectable

reference voltage 0.9V/1.0V/1.1V/1.2V and



Four operating modes

external reference input.

Normal mode: Both high and low clock active

Slow mode: Low clock only



8 interrupt sources

Sleep mode: Both high and low clock stop

6 internal interrupts: T0, TC1, CM0, CM1, SIO,

Green mode: Periodical wakeup by timer

UART

2 external interrupts: INT0 INT1



Package (Chip form support)

P-DIP 48 pins



Powerful instructions

LQFP 48 pins

One clock per instruction cycle (1T)

All ROM area JMP instruction.

All ROM area CALL address instruction.

All ROM area lookup table function (MOVC)

Содержание SN8P26L38









































































































































Результаты поиска

Содержание SN8P26L38

Отзывы:

Похожие инструкции для SN8P26L38

Бренды по названию

Популярные бренды

SONIX SN8P26L38, Руководство пользователя

Результаты поиска

Содержание SN8P26L38

Отзывы:

Похожие инструкции для SN8P26L38

Бренды по названию

Популярные бренды