SONIX SN32F280 Series Скачать руководство пользователя страница 168 | Manualshive

Страница: 168 / 268

background image

SN32F280 Series

32-Bit Cortex-M0 Micro-Controller

SONiX TECHNOLOGY CO., LTD

Page 168

Version 1.1



A data byte has been received while the I2C is in the addressed
slave receiver mode.

1

NACK

Assert NACK flag. HW will clear after issuing NACK automatically.
0: No function
1: An NACK will be returned during the acknowledge clock pulse on SCLn

when



A data byte has been received while the I2C is in the master
receiver mode.

R/W

0

0

Reserved

R

0

14.7.2 I2C n Status register (I2Cn_STAT) (n=0,1)

Address Offset: 0x04

Check this register when I2C interrupt occurs, and all status will be cleared automatically by writing I2Cn_CTRL or
I2Cn_TXDATA register.

While I2CIF =1, the low period of the serial clock on the SCL line is stretched, and the serial transfer is suspended.
When SCL is HIGH, it is unaffected by the state of I2CIF.

Following events will trigger I2C interrupt if I2C interrupt is enabled in NVIC interrupt controller.



START/Repeat START condition



STOP condition



Timeout



Data byte transmitted or received



ACK Transmit or received



NACK Transmit or received

Bit

Name

Description

Attribute

Reset

31:16

Reserved

R

0

15

I2CIF

I2C Interrupt flag.
0: I2C status doesn’t change.
1: Read



I2C status changes.

Write



Clear this flag.

R/W

0

14:10

Reserved

R

0

9

TIMEOUT

Time-out status
0: No Timeout
1: Timeout

R

0

8

LOST_ARB

Lost arbitration
0: Not lost arbitration
1: Lost arbitration

R

0

7

SLV_TX_HIT

0: No matched slave address.
1: Slave address hit, and is called for TX in slave mode.

R

0

6

SLV_RX_HIT

0: No matched slave address.
1: Slave address hit, and is called for RX in slave mode.

R

0

5

MST

Master/Slave status
0: I2C is in Slave state.
1: I2C is in Master state.

R

0

4

START_DN

Start done status
0: No START bit.
1: MASTER mode



a START bit was issued.

SLAVE mode



a START bit was received.

R

0

3

STOP_DN

Stop done status
0: No STOP bit.
1: MASTER mode



a STOP condition was issued.

SLAVE mode



a STOP condition was received.

R

0

2

NACK_STAT

NACK done status
0 : Not received a NACK
1 : Received a NACK

R

0

1

ACK_STAT

ACK done status
0 : Not received an ACK
1 : Received an ACK

R

0

0

RX_DN

RX done status
0: No RX with ACK/NACK transfer.

R

0

«
...
166
167
168
169
170
...
»

Содержание SN32F280 Series













































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SN32F280 Series

Бренд: Ubisys Страницы: 2

Бренд: Samsung Страницы: 27

Бренд: Paratec Страницы: 8

Бренд: J+J Страницы: 33

Бренд: EasyIO Страницы: 17

Бренд: YOKOGAWA Страницы: 33

Бренд: Samson Страницы: 70

Бренд: Qorvo Страницы: 6

Series RHCN-7000

Бренд: Omega Engineering Страницы: 2

Бренд: WAM Страницы: 2

Бренд: Zamel Страницы: 2

FP-SNS-SMARTAG1

Бренд: ST Страницы: 25

Бренд: SHOWTEC Страницы: 20

Бренд: LOVATO ELECTRIC Страницы: 6

Max Charge MC-614-H

Бренд: Balmar Страницы: 20

Бренд: Sierra Wireless Страницы: 58

Бренд: RollSeal Страницы: 58

Бренд: Chziri Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды