1
VERIFY MOTOR DIRECTION
1.
Press and release both the UP and DOWN buttons on a Telis transmitter simultaneously. The motorized treatment should jog UP then DOWN.
2.
Press and hold the DOWN button, if the shading system lowers or extends, press and release the UP and DOWN buttons simultaneously again. The treatment will
respond by jogging UP then DOWN.
3.
If the direction is incorrect, press and release the STOP button. The window treatment will now jog UP then DOWN. Press the UP and DOWN buttons simultaneously
to save the change in direction.
This step MUST be performed prior to any transmitters being memorized!
2
PROGRAMMING A CHANNEL INTO MEMORY
1.
Using a paper clip or similar instrument, press and hold the Programming/Memory Clear button on the MultiLink Plug-in for 2 seconds until the motor jogs. When
the motor jogs, release the Programming button. The MultiLink is now in programming mode.
2.
Select the desired channel to be memorized, then press and hold the programming button on a Telis Transmitter or similar device until the motor jogs. Once the
motor jogs, release the programming button. The transmitter is now memorized by the MultiLink Plug-in.
A. Initial Transmitter
1.
Press and hold (for 3 seconds) the programming button of a Telis Transmitter already memorized by the MultiLink Plug-in, but not the one to be removed. The
motor will respond by jogging.
2.
Press and hold the programming button on the transmitter or channel to be removed from memory until the motor jogs, then release. That transmitter will no longer
operate the MultiLink Plug-in.
3.
Alternately, using a paper clip or similar instrument, press and hold the Programming/Memory Clear button on the MultiLink Plug-in for 2 seconds until the motor
jogs. Once the motor jogs, release the programming button. Then press and hold the programming button on the Telis Transmitter to be removed from memory.
The motor will respond by jogging. That transmitter or channel will no longer operate the MultiLink Plug-in.
1.
Press and hold (for 3 seconds) the programming button of a Telis Transmitter already memorized by the MultiLink Plug-in. The motor will respond by jogging.
2.
Press and hold the programming button on the new transmitter or channel until the motor jogs, then release. The transmitter is now memorized by the MultiLink
Plug-in.
3.
Alternately, an additional transmitter can be programmed into memory by following the steps to memorize the initial transmitter as outlined in A above.
4.
Repeat these steps for each additional transmitter or channel - up to 8 total - to be stored in memory. If a 9th channel or transmitter programming is attempted, the
MultiLink will respond by jogging the window treatment, but any commands will be ignored.
B. Adding Additional Transmitters
C. Deleting Individual Transmitters
Upon power-up, the Multi-Link Plug-In is not programmed and will respond only to pressing the sequence button.
D. Deleting All Transmitters
1.
Using a paper clip or similar instrument, press and hold the Programming button on the MultiLink Plug-in for 7 seconds.
The motor will jog twice, once at 2
seconds and once at 7 seconds. When the motor is finished jogging, release the programming button. All transmitters are now removed from memory.
2.
Alternately, press and hold the UP and DOWN buttons simultaneously on a transmitter already memorized until the motor jogs. Press the UP button 4 times, pausing
at each switch press to verify that the motor jogs UP each time the UP button is pressed. Press and hold the STOP button until the motor jogs. All transmitters are
now removed from memory.
RADIO REMOTE OPERATION AND PROGRAMMING
1.
To lower or raise a window treatment, briefly press the UP or DOWN buttons of a Telis Transmitter or similar device.
2.
To stop the treatment, press the STOP button.
3a.
To enter TILT MODE, press the UP and STOP buttons simultaneously. Tilt Mode will remain active for 30 seconds.
3b.
Once in Tilt Mode, press and hold the UP or DOWN buttons on a Telis Transmitter. Release the button when the desired slat angle is reached.
4.
To exit Tilt Mode, press the UP and STOP buttons simultaneously. Otherwise Tilt Mode will end after 30 seconds, if no directions are activated.
NOTE:
During the 30 second tilt mode, both the Sequence and Programming buttons on the MultiLInk Plug-in are disabled.
Disabling Tilt Function
1.
Make sure the shade is not at the upper limit. Enter programming mode by pressing the UP and DOWN buttons of a Telis Transmitter simultaneously. The window
treatment will respond by jogging UP then DOWN.
2.
Press and release the UP button 3 times, pausing after each switch press to verify the motor jogs UP. Press and release the STOP button, the shade will respond by
jogging. The Tilt function described above is now disabled.
3.
To re-enable the tilt function, simply repeat steps 1 & 2 above.
3
LIFT/TILT OPERATION
