Dexxo Pro io
Copyright © 2015 Somfy SAS. All rights reserved
10
EN
Obstacle detection action during closure
Values
VWRSSDUWLDOUHRSHQLQJ
3: fully reopen
Automatic closure time delay
Values
0 to 12 (time delay value = value x 10 s)
2: 20 s
Lighting time delay
Values
WRWLPHGHOD\YDOXH YDOXH[V
6 : 60 s
Comments
5HPDUN'XHWRWKHWKHUPDOFXWRXWSURWHFWLRQV\VWHPWKH
integrated light may cut out automatically if it is used for an
extended length of time. We therefore recommend selecting
a light time delay in excess of 2 mn (t1=12 or 120s) only
when remote lighting is used.
> Programming example: setting the ”P7” closure approach
speed (Fig. 39)
Setting up a long soft stop function zone
“P7” = 2
.
> Special case: adjusting the position of the door for partial
opening (Fig. 40)
Select setting “
P6
´DQGYDOLGDWHE\SUHVVLQJ³
OK
´
0RYHWKHGRRUWRWKHGHVLUHGSDUWLDOO\RSHQSRVLWLRQ
- Pressing and holding the
“-”
button will close the door.
- Pressing and holding the
“+”
button will open the door.
- Validate by pressing “
OK
´
- Exit the menu with “
SET
´
> Forced mode (Fig. 41)
This function makes it possible to manipulate the door at any moment (loss of
remote control, photoelectric cell fault, etc.).
'RRUVWDWLRQDU\
- press the
“-”
button to close it
- press the
“+”
button to open it.
'RRUPRYLQJSUHVVWKH
“-”
or
“+”
button to stop the door.
> Programming a Situo Telis Composio Impresario type remote
control (Fig. 42)
Before programming the remote control, make sure that it has already
PHPRULVHGWKHV\VWHPNH\5HIHUWRWKHFRUUHVSRQGLQJUHPRWHFRQWURO
documentation).
[1].
Press the “
PROG
´EXWWRQRQ'H[[R3URXQWLOWKHOLJKWFRPHVRQ
[2].
%ULHÀ\SUHVVWKH³
PROG
´EXWWRQRQWKHUHPRWHFRQWURO
Wait for the Dexxo Pro light to blink.
This may take from a few seconds to around a minute depending on the
number of products connected to the system.
5HPDUN'H[[R3URFDQPHPRULVHXSWR6LWXRUHPRWHFRQWUROV)RURWKHU
types of remote controls, no limit applies.
8 - PROGRAMMING KEYGO IO REMOTE
CONTROLS FOR FULL AND PARTIAL
OPENING OPERATION
In order for the garage door to open fully and partially, parameter P4 must be
activated (refer to the section entitled "Parameter setting").
When parameter P4 is activated, all the remote control buttons
previously programmed during commissioning become programmed
buttons to partially open the garage door.
$QDGGLWLRQDOPHPRULVLQJFRPPDQGPXVWEHSHUIRUPHGRQEXWWRQV
ZKLFKDUHXVHGWRIXOO\RSHQWKHJDUDJHGRRU
The operations to be performed differ according to the desired function for
the button being programmed (full or partial opening), and depending on
the memorisation which has already been performed on the button prior to
activation of parameter P4.
> Switch to full opening for a button previously memorised
during commissioning (Fig.43)
[1].
Simultaneously press the large button and the small button in the centre
of the remote control.
7KHUHPRWHFRQWUROLQGLFDWRUOLJKWÀDVKHV
[2].
Press the remote control button previously memorised during
commissioning within 10 seconds.
The button for full opening has been memorised.
> Memorise a button that has not yet been programmed to
trigger partial opening (Fig.23)
[1].
Press the “
PROG
´EXWWRQRQWKH'H[[R3URXQWLOWKHOLJKWFRPHVRQ
seconds).
[2].
Simultaneously press the outer right and outer left buttons on the remote
control.
7KHUHPRWHFRQWUROLQGLFDWRUOLJKWÀDVKHV
[3].
%ULHÀ\SUHVVWKHVHOHFWHGEXWWRQWRSDUWLDOO\RSHQWKH'H[[R3URPRWRU
7KHOLJKWRIWKH'H[[R3URPRWRUÀDVKHVIRUVHFRQGV
The button for partial opening has been saved.
> Memorise a button that has not yet been programmed to
trigger full opening (Fig. 44)
[1].
Press the “
PROG
´EXWWRQRQWKH'H[[R3URXQWLOWKHOLJKWFRPHVRQ
seconds).
[2].
Simultaneously press the outer right and outer left buttons on the remote
control.
7KHUHPRWHFRQWUROLQGLFDWRUOLJKWÀDVKHV
[3].
%ULHÀ\SUHVVWKHVHOHFWHGEXWWRQWRRSHUDWHWKH'H[[R3URPRWRUIRUIXOO
opening.
7KHOLJKWRIWKH'H[[R3URPRWRUÀDVKHVIRUVHFRQGV
[4].
Simultaneously press the large button and the small button in the centre
of the remote control.
7KHUHPRWHFRQWUROLQGLFDWRUOLJKWÀDVKHV
[5].
Press the remote control button that you wish to use for full opening within
10 seconds.
The button for full opening has been memorised.
9 - PROGRAMMING KEYTIS IO REMOTE
CONTROLS FOR FULL AND PARTIAL
OPENING OPERATION
In order for the garage door to open fully and partially, parameter P4 must be
activated (refer to the section entitled "Parameter setting").
When parameter P4 is activated, all the remote control buttons
SUHYLRXVO\ VDYHG GXULQJ FRPPLVVLRQLQJ DUH SURJUDPPHG WR IXOO\
RSHQWKHJDUDJHGRRU$QDGGLWLRQDOFRPPDQGPXVWEHSHUIRUPHG
on buttons which are used to partially open the garage door.
> Save a button that has not yet been programmed to trigger
partial opening (Fig.45)
[1].
Save the button on the Dexxo Pro (refer to the section on "Programming
XVLQJWKH'H[[R3URPRWRURQSDJH
[2].
Simultaneously press the saved button and the “
STOP
´ EXWWRQ RQ WKH
remote control.
The remote control beeps twice.
The button for partial opening has been programmed.
> Switch to partial opening for a button previously saved during
commissioning (Fig. 46)
Simultaneously press the saved button and the “
STOP
´EXWWRQRQWKHUHPRWH
control.
The remote control beeps twice.
The button for partial opening has been programmed.
> Switch a button previously programmed for partial opening to
full opening (Fig. 47)
Simultaneously press the saved button and the “
STOP
´EXWWRQRQWKHUHPRWH
control.
The remote control beeps 3 times.
The button for full opening has been programmed.
