SOMFY Elixo 500 3S RTS, Руководство по установке

Страница: 22 / 88

EN
Elixo 500 3S RTS
20
Copyright © 2015 Somfy SAS. All rights reserved
DIAGNOSTICS
Operating code display
Code Description Comments
C1 Awaiting command
C2 Gate opening
C3 Awaiting gate closure Automatic closing time delay P02, P04 or P05 in progress.
C4 Gate closing
C6 Detection in progress for cell safety
Displayed during a movement request or during movement when detection is in progress on the safety input.
The display appears for as long as detection is in progress on the safety input.
C7 Detection in progress for safety edge safety
C8 Detection in progress for programmable safety
C9 Detection in progress for emergency stop safety
C12
5HLQMHFWLQJFXUUHQW
C13 Safety device autotest in progress Displayed while the autotest is running on the safety devices.
C14 Permanent complete opening wire control input Indicates that the complete opening wire control input is permanently activated (contact closed). Commands
coming from the radio remote controls are then disabled.
C15 Permanent pedestrian opening wire control input Indicates that the pedestrian opening wire control input is permanently activated (contact closed). Commands
coming from the radio remote controls are then disabled.
C16 BUS cell programming refused Check that the BUS cells (wiring, alignment, etc.) are operating correctly
Cc1 9.6 V power supply Displayed during operation with 9.6 V backup battery
Cu1 24 V power supply Displayed during operation with 24 V backup battery or solar supply
Programming code display
Code Description Comments
H0 Awaiting setting Pressing and holding the " SET " button for 2 seconds starts self-learning mode.
Hc1 Awaiting s 9.6 V power supply Displayed during operation with 9.6 V backup battery
Hu1 Awaiting s 24 V power supply Displayed during operation with 24 V backup battery or solar supply
H1 Awaiting start of self-learning Pressing the " OK " button starts the self-learning cycle.
Pressing the " + " or " - " button allows the motor to be controlled in forced operation mode.
H2 Self-learning mode - opening
H4 Self-learning mode - closing
F0 Awaiting remote control memorisation for
operation in complete opening mode Pressing a button on the remote control allocates this button to the motor complete opening control.
Pressing "
PROG " once more switches to "awaiting remote control memorisation for operation in pedestrian opening
mode: F1 ".
F1 Awaiting remote control memorisation for
operation in pedestrian opening mode Pressing a button on the remote control allocates this button to the motor pedestrian opening control.
Pressing "
PROG " once more switches to "awaiting remote lighting control memorisation: F2 ".
F2 Awaiting remote control memorisation for
remote lighting control Pressing a button on the remote control allocates this button to the remote lighting control.
Pressing "
PROG " once more switches to "awaiting auxiliary output control memorisation: F3 ".
F3 Awaiting remote control memorisation for
auxiliary output control Pressing a button on the remote control allocates this button to the remote lighting control.
Pressing "
PROG " once more switches to "awaiting remote control memorisation for operation in complete opening
mode: F0 ".
Fault and breakdown code display
Code Description Comments Solution?
E1 Cell safety autotest fault The cell autotest is not satisfactory.
&KHFNWKDW3LVFRUUHFWO\FRQ¿JXUHG
Check the wiring of the cells.
E2 Programmable safety autotest fault The programmable safety input autotest is
not satisfactory.
&KHFNWKDW3LVFRUUHFWO\FRQ¿JXUHG
Check the programmable safety input wiring.
E3 Defective safety edge autotest The safety edge autotest is not satisfactory.
&KHFNWKDW3LVFRUUHFWO\FRQ¿JXUHG
Check the safety edge wiring.
E4 Obstacle detection when opening
E5 Obstacle detection when closing
E6 Cell safety fault
Detection in progress on safety input for
longer than 3 minutes.
Check that no obstacles are causing the cells or safety edge to detect.
&KHFNWKDW33RU3LVFRUUHFWO\FRQ¿JXUHGLQUHODWLRQWRWKH
device connected to the safety input.
Check the safety device wiring.
Check that the photoelectric cells are correctly aligned.
E7 Safety edge safety fault
E8 Programmable safety fault
E10 Motor short circuit protection Check the motor wiring.
E11 24V power supply short protection Short circuit protection for input/outputs:
product and additional devices connected to
terminals 21 to 26 (orange light, photoelectric
cells (except BUS), code keypad, safety
edge) not operating Check the wiring, then disconnect the power supply for 10 seconds.
N.B.: maximum accessories consumption = 1.2 A
E12 Hardware fault The hardware auto tests are not satisfactory Repeat an order. If the fault persists, contact Somfy.
E13 Accessories power supply fault The accessories power supply cuts
out following an overload (excessive
consumption) N.B.: maximum accessories consumption = 1.2 A
Check the consumption of the connected accessories.
E15 Fault when the motor supplied by the
EDFNXSEDWWHU\LV¿UVWVZLWFKHGRQ
Disconnect the backup battery and connect the motor to the mains to switch it
RQIRUWKH¿UVWWLPH
For all other error codes or faults, please contact Somfy.