background image

Power Input

Input port for 24V DC 

power from power supply

I. OVERVIEW

SDN Motor limits must be set prior to installing Digital Motor Interface

NOTE: Refer to the respective motor instructions on how to set the limits

All connections must be properly made according to the wiring diagrams on the product instructions

Fully commissioned Control4 system

Control4 Composer Software OS 2.9.0 or higher
Somfy Control4 to Digital Motor Interface driver

The Control4 to Digital Motor Interface (DMI) receives and sends bi-directional commands and feedback 

connected between Somfy wired SDN RS485 motors and a Control4 Zigbee system as a wireless end node. 

It receives Control4 Zigbee transmissions and converts them to motor control commands for Somfy’s line of 

line voltage (AC) and low voltage (DC) SDN RS485 motors.

S Y S T E M   R E Q U I R E M E N T S

C O N N E C T I O N S   &   I N D I C A T O R S

M O T O R   A D A P T O R   C A B L E

When installing the Digital Motor Interface (DMI) with DC motors, the Data & Power Adaptor Cable (Ref # 9027112, sold separately) is required 

for proper installation. Using the DMI with AC SDN RS485 motors requires the Somfy Grey Motor Data Cables (sold separately).

3 of 10

Power Output

Output port for 24V DC 

power to motor

SDN Port

Connect to motor or 

Data & Power Cable

Push Button

Leaving the Zigbee 

network, restart identify 

& manual operation

LED BEHAVIOR

:

(LEFT)

OFF

NO POWER TO DEVICE

GREEN

POWER TO DEVICE

LED BEHAVIOR

:

(RIGHT)

ORANGE

>

GREEN

(Solid>Flashing)

SDN MOTOR ACTIVITY

GREEN

(Flashing)

NO MOTOR FEEDBACK

ORANGE

(Flashing)

INCLUSION MODE

ORANGE

(Solid)

CONNECTED TO ZIGBEE NETWORK

Control4 Digital Motor 

Interface Connection

Connect to SDN Port on the 

Digital Motor Interface 

Power Supply 

Connection

Connect to the power 

supply to provide power  

Digital Motor 

Connection

Connect to SDN RS485 

Digital Motor Cable(s) 

Each DMI is limited to one SDN RS485 motor connection

During power-up, the RIGHT 

LED will flash indicating the 

firmware version. 

Refer to product instructions for 

more detail.

Содержание CONTROL4











Отзывы: