SOMFY animeo IB+ 4 Zone Touch Building Controller Скачать руководство пользователя

Страница: 38 / 49

animeo IB+

4 Zone/8 Zone TouchBuco BACnet

2020/04/30

Seite 38

Learn all to selected zone:

By pressing the "START" button, all motor controllers connected to TouchBuco at that time will be assigned

to the selected zone. Only the corresponding motor controllers assigned to a zone should therefore be

connected to the TouchBuco via the IB+ cable.

6.5.2.3 Run/Tilt Times

You can navigate through the setting process using the grey arrows.

Runtime

The runtime is the time required by an end product/motorized product (roller shutters, Venetian blinds, etc.)

to move from its uppermost position (0 %) to its lowermost position (100 %) and vice versa. With windows,

the runtime is from fully open (100 %) to fully closed (0 %). The runtime is important to ensure that an end

product/motorized product can also be moved into an intermediate position (defined in percent from 0 % to

100 %).

In the case of large/long motorized products/end products, the runtime during downward travel can devi-

ate from the runtime for upward travel by several seconds (total distance covered by end product/motorized

product moving up and down).

When using end products/motorized products with turning (e.g. Venetian blinds): If a position and an angle

are to be approached, the runtime must be entered very accurately, as the rotation for the angle only starts

once the runtime entered has elapsed.

If there are motorized products of varying lengths within a given zone, you must enter the longest time first.

You can make precision adjustments for the shorter motorized products in this zone later under "Settings".

Angle

The angle is the time required by a Venetian blind to turn the slats from fully closed to fully open. This time is

typically in the range from 0.8 to 2 seconds.

Positioning accuracy better than +/- 5° is generally not achieved. This is due to the mechanical systems

employed and does not have any negative impact on the sun protection function.

Other/Backlash

This setting is used to compensate for mechanical play in the Venetian blind when changing rotary direction.

A value of 0.2 to 0.3 seconds is typically set. In the case of roller shutters, this time should be 0.0 seconds.

Other/Start delay

Start delay when using an electronic drive: An electronic drive has different start-up behavior from a standard

drive. The start-up time delay improves operator ergonomics and the positioning accuracy of the end prod-

uct/motorized product. This time is set to 0.2 seconds. With the standard drive, it is set to 0 seconds.

The electronic Somfy drives are: WT range (Oximo, Ilmo, Orea), J4WT.

The standard Somfy drives are: LT range, SLT range, LS range, J4 (without WT designation, e.g. HTM)

For non-Somfy drives, please get in touch with your specialist or the respective manufacturer.

Switch Config

"EU"

Short keystroke = change step/stop, long keystroke = up/down.

"US"

Short keystroke = up-down/stop, long keystroke = change step.

"Tilt only" Venetian blind can only be tilted in its current position.

"Roller"

Short/long keystroke = up/down/stop

"Deadman"

Movement commands are only carried out while the button is depressed

Содержание animeo IB+ 4 Zone Touch Building Controller

















































Результаты поиска

Содержание animeo IB+ 4 Zone Touch Building Controller

Отзывы:

Похожие инструкции для animeo IB+ 4 Zone Touch Building Controller

Бренды по названию

Популярные бренды

SOMFY animeo IB+ 4 Zone Touch Building Controller, Руководство пользователя

Результаты поиска

Содержание animeo IB+ 4 Zone Touch Building Controller

Отзывы:

Похожие инструкции для animeo IB+ 4 Zone Touch Building Controller

Бренды по названию

Популярные бренды