Sollae Systems CIE-H10A Скачать руководство пользователя страница 15

Страница: 15 / 80

CIE-H10A User Manual Ver. 1.1

- 14 -

https://www.ezTCP.com

1.6.4

Ethernet Interface

An RJ45 connector is for the network interface of CIE-H10A. You can use a UTP cable. It

automatically senses 10Mbits or 100Mbits Ethernet. It also provides auto MDI/MDIX
function that can automatically sense a 1:1 cable or cross over cable.

Each Ethernet device has its own hardware address (MAC address). CIE-H10A is shipped

to the market with the hardware address set in the factory.

Figure 1-10 the RJ45 connector

⚫

Status of the system RJ45 LED

Color

LED status

Description

Yellow

Off

10 Mbps

100 Mbps

Green

Connecting with Ethernet

Off

Not connecting with Ethernet

Blinking

When sending/receiving network data

Table 1-8 LED status on the RJ45 LED

1.6.5

Power

CIE-H10A can be powered by 5VDC source via power jack. The specifications of the

power jack are as follows:

Figure 1-11 the power specification

Содержание CIE-H10A

















































































Результаты поиска

Содержание CIE-H10A

Отзывы:

Похожие инструкции для CIE-H10A

Бренды по названию

Популярные бренды

Sollae Systems CIE-H10A, Руководство пользователя

Результаты поиска

Содержание CIE-H10A

Отзывы:

Похожие инструкции для CIE-H10A

Бренды по названию

Популярные бренды