background image

SOLiD RocketWAVE™ SRF-L-1835 Product Manual   

V1.6 - DEC 2021 

© 2021 SOLiD, Inc. All Rights Reserved. Confidential & Proprietary. 

 

Page 6 

(via local supply connection) and/or coarse protection (external surge protection) is recommended de-

pending on the individual application in order to avoid damage caused by overcurrent.   

Input voltage: 100~240 V; Input AC frequency: 50Hz ~ 60Hz;   

Output voltage: 12 V; Output current: 2.0 A;   

Output power: 24.0 W; Average operational efficiency: 85%; Efficiency at light load (10%): 85%;   

Power consumption at no load: <0.1W 

 

The repeater complies with European standard EN60950-1/EN62368-1. 

 

To be sold exclusively to mobile operators or authorized installers - no harmonized fre-

quency bands, operation requires license. Intended use: EU and EFTA countries. 

Indicates conformity with the RED directive 2014/53EU and/or RoHS directive 2011/65/EU. 

 

Declaration of Conformity:

 SOLiD declares that the radio equipment type Repeater is in compliance 

with Directive 2014/53/EU. The Full text of the EU declaration is available at the following website:   

https://solid.com/emea/resources/product-literature/

 

 

WEEE Recycling:

 SOLiD complies with collection and recycling arrangements per the Waste Electrical 

and Electronic Equipment (WEEE) Directive and implementing regulations. See more information at: 

https://solid.com/emea/resources/product-literature/

 

 

 

For all technical support or product return requests, please ensure you have the SOLiD product identification and 

serial number available. These can be found located on the back of the unit. The site and customer name should 

also be included in all communications. All faulty units must be returned in their original or suitable protective 

packaging.   

 

Please contact SOLiD the local office or send an email via one of the following email addresses: 

SOLiD EU GmbH 

Gartenstr. 5, 87448 Waltenhofen, Germany 

[email protected] 

 

 

 

 

Содержание RocketWAVE SRF-L-1835

























Отзывы: