Soleus GPS One
Step 2) Charging the Battery:
Charge the unit for at least 4-5 hours before first use. The length of time for a fully charged
battery will last depending on the actual usage. It is also recommended to regularly re-charge
your battery every 1-2 months even if it is not used to maintain good battery condition.
2.1)
Plug your USB cable to your PC
2.2)
Align the charging clip with the 4 contact pins on the back of the watch.
2.3)
Connect the charging clip securely to the watch. The watch will display CHARGE and the
percentage charge level of the battery. There is also a scrolling line at the middle.
Note: Please thoroughly dry the charging contacts and surrounding area to ensure proper
electrical contact and prevent corrosion.
When the battery is low, it is time to charge the GPS watch. Once the battery is full, it will
display “ 100% FULL CHARGE”.
Step 3) Configure your watch:
TIME mode
•
Press and hold S11 until the “TIME” blinks.
•
Press S1/S11 to select: TIME, NIGHT, UNIT, USER, AUTOLAP and CONTRAST.
•
Press S5 to enter selected views.
Setting the Time:
o
While “TIME” is blinking, Press S5.
o
Set the HOUR by pressing S1/S11 and press S5.
o
Set the MINUTE by pressing S1/S11 and press S5.
o
Set the SECOND by pressing S1/S11 and press S5.
o
Set the YEAR by pressing S1/S11 and press S5.
o
Set the MONTH by pressing S1/S11 and press S5.
o
Set the DAY by pressing S1/S11 and press S5.
o
Set the 12/24H by pressing S1/S11 and press S5.
o
Press S5 to confirm and set M-D / D-M format setting.
o
Press S1/S11 to change the setting.
o
Press S5/S7 to confirm setting.
Setting the Night:
•
Press S5 while “NIGHT” is blinking. The watch will display Night ON or OFF.
•
Press S1/S11 to change ON or OFF.
•
Press S5/S7 to confirm setting.
Setting the Unit:
•
Press S5 while “UNIT” is blinking. KM
will start to blink.
•
Press S1/S11 to change the unit.
•
Press S5/S7 to confirm setting.
Setting the User’s information:
•
Press S5 while “USER” is blinking. MALE
will start to blink.
•
Press S1/S11 to change the gender.
•
Press S5 to confirm and set the AGE.
•
Press S1/S11 to change the age digits.
•
Press S5 to confirm and set the WEIGHT.
•
Press S1/S11 to change the weight digits.
•
Press S5 to confirm and set the HEIGHT.
•
Press S1/S11 to change the height digits.
•
Press S5/S7 to confirm setting.
Setting the Auto Lap
:
•
Press S5 while “AUTO LAP” is blinking. Auto lap
1
will start to blink.
•
Press S1/S11 to change the setting.
•
Press S5/S7 to confirm and set ALERT ON or OFF.
•
Press S1/S11 to change the setting.
•
Press S5/S7 to confirm setting.
Setting the Contrast:
•
Press S5 while “CON-TRAST” is blinking. The watch will display the Contrast percentage.
•
Press S1/S11 to change to your desired value (LCD Contrast range: 10% to 100%).
•
Press S5/S7 to confirm setting.
Step 4) Acquire Satellite signals:
To get the correct time of day and begin using your GPS watch, you have to acquire the
Satellite signals. It may take few minutes to acquire the satellite signals. Press S1 or S7 to
search the signal.
4.1)
Go outside to an open area away from tall buildings and trees. Orient the GPS antenna
towards the sky for best reception. The antenna is located at the 6 o’clock position of the
watch.
Note: In order to accurately navigate the GPS, you need to have a good line of sight
to the satellites.
4.2)
Stand still and do not begin moving while locating the Satellite until the signals are already
received.
4.3)
If no Satellite signal is received, after approx. 15 minutes, the watch will go to INDOOR
screen.
