Soleus Air HGW-308 Скачать руководство пользователя страница 7

Страница: 7 / 11

ASSEMBLY - INSTALLATION

Required Tools for Floor Use:

Phillips screwdriver (not supplied)

Estimated Assembly Time for Floor Use:
1 minute

Assembly Instructions for Floor Use:

Insert the feet and bolts onto the unit as shown in the
diagram.

Required Tools for Wall Mounting:

Phillips screwdriver (not supplied)
Drill (not supplied)
Hammer (not supplied)

Estimated Mounting Time: 5 minutes

Mounting Instructions:

STEP 1
Using the mounting support as a guide, mark the first screw
hole on the wall using the tip of a long nail.

STEP 2
Move the mounting support, and drill the first screw hole.

STEP 3
Insert the first mounting anchor into the drilled hole.

STEP 4
Place the mounting support on the wall. Insert a screw through
the mounting support and anchor. Tighten the screw lightly.

STEP 5
Use the other side of the mounting support to mark the second
screw hole on the wall [approximately 5 7/16 in.].

STEP 6
Move the mounting support, and drill the second hole.

STEP 7
Insert the second mounting anchor into the drilled hole.

STEP 8
Place the mounting support on the wall. Insert the second screw
through the mounting support and anchor. Firmly tighten both
screws.

STEP 9
After mounting the heater, insert two screws into the bottom
holes and secure the heater to the wall for safety purposes.

Содержание HGW-308











