background image

1.800.627.4499

18

GR90, EV90, EV90P

ERV

MAINTENANCE

DIFFERENTIAL STATIC ACROSS CORE DSP VS. CFM

EV

90

, G

R90

DSP

0.10

0.20

0.30

Fresh Air (FA) CFM

42

84

127

Room Air (RA) CFM

42

84

127

DIFFERENTIAL STATIC ACROSS CORE DSP VS. CFM

EV

90P

DSP

0.10

0.20

0.30

Fresh Air (FA) CFM

58

115

173

Room Air (RA) CFM

58

115

173

The proper airflow range 
for the models are 40-110 
CFM.

 CAUTION

Make sure clean filters are 
installed before balancing 
air flow. Dirty or clogged 
filters reduce airflow 
through the unit.

 CAUTION

Keep your ERV performing at its best by cleaning it as described below.

5.1 TO CLEAN THE ENERGY EXCHANGE ELEMENT

  1. Remove the filters (see below). 
  2. Vacuum the exposed faces of the energy exchange core with a soft brush attachment. 
  3. After servicing the filters, re-install them (see below). 
  4.  Vacuum out dust from the rest of the unit case. Dust collects only on the entering faces 

of the energy exchange core. The interior of the energy exchange core stays clean even if 
the core faces are dust covered. The core flutes move the air in a laminar airflow such that 
particulate deposition is maintained at virtually nill.

5.0 MAINTENANCE

5.2

 

INSPECT AND CHANGE THE FILTERS REGULARLY 

Service filters every three months when the unit is in regular use or as needed to keep them 
reasonably clean. 
  1. Release cam latches and carefully swing access door open. Remove the door by sliding to 
      one side. 
  2. Remove filter clips. 
  3. Pull the filters out. 
  4. Vacuum with a hose attachment. 
  5. Re-install filters and filter clips, see Section 5.5 Service Parts. Orange side of filter should  
      face the core.
  6. Re-install door, and fasten cam latches.
The primary contact for replacement filters for your RenewAire unit is the installing contractor. 
As an alternative, you may wish to produce your own filters. Please follow these instructions:
Filters may be cut from a sheet or roll of ¾"–1" firm, spun polyester filter “hog hair” media or 
material, similar to the existing filter in the residential unit.
The size of each filter (2 required per unit) is as follows:

 EV90/GR90

 

9 ½" x 10 ½" 

 

EV90P  

21 ¾" x 10 ½"

Call your HVAC contractor or RenewAire for further information.

DO NOT WASH THE  

ENERGY EXCHANGE CORE.

Keep it away from water 
or fire to avoid damaging 
it. Always handle the core 
carefully.

 CAUTION

Risk of Fire, Electric Shock, 

or Injury.

u

   Before servicing or  

cleaning the unit, unplug 

the line cord. 

u

   Make sure unit is not 

running before opening its 

door. Blower wheels are 

sharp and can cut.

u

   Do not disable the  

interlock switch: it is there 

for your safety.

 WARNING

NOTE: The filters 
should be replaced 
after they have 

been cleaned several 
times.

NOTE: Filters must 
be used or the 
face of the energy 

exchange core will become 
blocked by dust and 
reduce unit efficacy. The 
filters supplied in the unit 
are usually able to keep 
the energy exchange core 
clean for many months. 
Finer filters can be used 
but must be cleaned more 
often.

Содержание RenewAire ERV Series





















Отзывы: