Solectek 70MOB1 Скачать руководство пользователя | Manualshive

Страница: 3 / 47

background image

1. Introduction

Congratulations on your purchase of a SkyWay-Mobile BTS system. This user’s guide
contains basic description of the system, basic installation and configuration steps to act as
a basic guideline for the end user. This guide is not to act as a step-by-step guide for self-
installation by end users.

This product requires a full professional installation services by Solectek’s field engineering
staff or authorized reseller officially certified by Solectek. The installation services will
include the following work:

Site survey and RF planning.

Drive test, mapping of the coverage area.

Physical mounting of the outdoor components on tower or rooftop

Antenna

alignment

Configuration, calibration and troubleshooting

Commission of the service

Product Features

The SkyWay-Mobile BTS unit has the following features

Throughput – up to 15 Mbps in a 5 MHz channel BW.

Chanel BW – 1, 2, 3, 4, or 5 MHz, user configurable

Support for more than 300 subscribers

Support for 150 simultaneous phone calls

N=1

Frequency

reuse

Voice service support – proprietary mode or VoIP

«
1
2
3
4
5
...
»

Содержание 70MOB1
















































Отзывы:

Нет отзывов

Похожие инструкции для 70MOB1

Бренд: LAUMAS Страницы: 40

Бренд: Oce Страницы: 255

Бренд: IFM Страницы: 12

Бренд: IFM Страницы: 13

Efector 200 Series

Бренд: IFM Страницы: 4

Бренд: IFM Страницы: 33

WORKCENTRE C2424

Бренд: Xerox Страницы: 2

Бренд: NavLinkz Страницы: 4

Бренд: Kuda-Phonebase Страницы: 3

Бренд: yasuni Страницы: 8

Бренд: HYPERLOW Страницы: 4

Бренд: mantona Страницы: 24

Бренд: Schumacher Electric Страницы: 12

Бренд: REVCAMUK Страницы: 4

Бренд: SMC Networks Страницы: 80

Бренд: Actia Страницы: 37

Бренд: AC Schnitzer Страницы: 20

Бренд: Datasensor Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды