Dyaco Canada Inc. 2016
10
E95
ASSEMBLY INSTRUCTIONS
1
2
INCLINE
RAIL
& CONSOLE
MAST
See Page 11 for Illustration
1.
Install the Incline Rail Assembly (
2
) into the U-channel bracket of the Main
Frame (
1
). Secure with the six bolts & associated hardware as follows: From the
sides install two Hex Head Bolts (
133
) with two Flat Washers (
164
) and two
Nylon Nuts (
157
). From the top install four Hex Head Bolts (
135
), four Split
Washers (
182
), four Flat Washers (
170
), and four Star Washers (
183
), and
tighten with the Wrenches provided (
184
&
187
).
2.
Connect the three Wire Harness (
48
) to the female receiver cable coming from
the Incline Rail Assembly (
2
). Connect the Three pin position Sensor Connector
(
49
) to the female receiver coming from the Incline Rail Assembly (
2
). Mate red,
white, and black wires together.
3.
Locate the Console Mast (
12
) and Console Mast Cover (
96
) and slide the cover
onto the mast as far as it will go. Make sure the Console Mast Cover is facing
the correct way. At the top opening of the Main Frame of the elliptical is a
Computer Cable (
50
). Secure the free end of the twist tie that exits the bottom
of the Console Mast (
12
) to this cable. Pull the opposite end of this twist tie up
through the Console Mast (
12
) until the cable exits the top.
Install the Console Mast (
12
) into the receiving bracket on the top of the Main
Frame (
1
). Pull slightly on the Computer Cable at the top of the mast while
installing. This will ensure the cable does not get pinched and shorted during
Console Mast Assembly.
4.
Put one Split Washer (
180
) onto the Long Hex Head Bolt (
125
) and install
through the left side of the receiving bracket into the Console Mast (
12
). Put
the two Curved Washers (
181
) onto the two Short Hex Head Bolts (
132
) and
install through the front of the console mast. Using Wrench (
184
), tighten the
(
132
) bolts first, then the (
125
) bolt, and lastly the fourth bolt, which is pre-
installed, firmly. These bolts should be tightened as much as you possibly can.
This is the main joint of the unit. If not tightened sufficiently, this could lead to noise
and instability issues.
5.
Plug all of the connectors into the back of the console; Computer Cable (
50
),
two Hand pulse Cables (
56 & 56-1
), Resistance Switch Wire (
60
) and Incline
Switch Wire (
59
). Secure the Console (
45
) on the console mounting plate with
four Phillips Head Screws (
141
) using the Screw Driver (
186
).
Note
: there will be an
empty four pin port on the back of the console. This model doesn’t use this port.
LOWER
HANDLE BAR ARMS
See Page 11 for Illustration
1.
Install two Wave Washers (
175
) onto the Left and Right sides of the Handle Bar
axle.
2.
Slide the Left (
13
) and Right (
14
) lower handle bar arms onto the appropriate
side of the axle. The handlebars have a small sticker on them indicating L (left)
and R (right).
Make sure the handlebars are facing the correct direction – see illustration.
3.
Install two Flat Washers (
165
) onto the two Hex Head Bolts, (
132
) and install
and tighten in the threaded holes in the ends of the axle with a Wrench (
187
).
4.
Untie the wire holding the Sleeve Spacer (
24
) in place on the rod-end of the
Lower Handle Bar Arms (
13
&
14
). Align the hole in the rod ends with the hole
in the brackets of the left and right Handle Bar (
13
&
14
). The end of
connecting
arms should be positioned inside the Handle Bar bracket. Secure with a Hex Head
bolt (
134
), Flat Washer (
170
) and Nylon Nut (
159
) by using the Wrenches provided
(
184
&
187
).
#125
. 3/8” x 2-1/4” Hex
Head Bolt (1 pcs)
#132
. 3/8” x 3/4”
Hex Head Bolt (2 pcs)
#133
. 3/8” x 1-1/2” Hex
Head Bolt (2 pcs)
#135
. 5/16” x 2-1/4” Hex
Head Bolt (4 pcs)
#141
. M5 x 10mm
Phillips Screw (4 pcs)
#157
. 3/8” x 7T Nylon Nut
(2 pcs)
#164
. 3/8” x 19 x 1.5T Flat
Washer (2 pcs)
#170
. 5/16” x 20 x 1.5T
Flat Washer (4 pcs)
#180
. 3/8” x 2T Split
Washer (1 pc)
#181
. 3/8” x 23 x 2T
Curved Washer (2 pcs)
#182
. 5/16” x 1.5T Split
Washer (4 pcs)
#183
. 5/16”
Sta
r
Washer (4 pcs)
#132
. 3/8” x 3/4”
Hex Head Bolt (2 pcs)
#134
. 5/16” x 1-1/4”
Hex Head Bolt (2 pcs)
#159
. 5/16” x 7T
Nylon Nut (2pcs)
#165
. 3/8” x 30mm
Flat Washer (2 pcs)
#170
. 5/16” x 20 x 1.5T
Flat Washer (2 pcs)
#175
. 25mm
Wave Washer (4 pcs)
HARDWARE
STEP 1
HARDWARE
STEP 2
Содержание 16608600950
