Sole Fitness E20, Руководство пользователя

Страница: 14 / 32

12 E20 / E25 ELLIPTICAL
1. Attach the Lower Swing Arms (L) and (R), ( 12 ) and ( 13 ), on each side of
Console Mast shaft and secure with two Hex Head Bolts ( 104 ) and two Flat
Washers ( 138 ) by using the Wrench ( 152 ).
2. Insert the shaft of the left Connecting Arm ( 10 ) through the bushing on left
Pedal Arm ( 7 ) and secure with a Button Head Socket Bolt ( 115 ) together with
a Flat Washer ( 138 ) by using M5 L Allen Wrench ( 149 ). Do it the same way for
right Connecting Arm ( 11 ) and right Pedal Arm ( 8 ).
3. Remove the Rod End Shaft ( 20 ), Flat Washer ( 138 ) and Hex Head Bolt ( 104 )
which are on the left and right Connecting Arms. Connect the Connecting
Arm with the Lower Swing Arm and secure with Rod End Shaft ( 20 ), Flat
Washer ( 138 ) and the Hex Head Bolt ( 104 ) by using the Wrench provided
( 152 ).
LOWER
SWING ARMS
#104 . 5/16” x 15mm
Hex Head Bolt (2 pcs)
#115
. 5/16” x 15mm
Button Head Socket Bolt
(2 pcs)
#138 . Ø8.5 × 26mm × 2T
Flat Washer (4 pcs)
HARDWARE STEP 1
1. Connect the Front Stabilizer Bar (2) with the Main Frame at the front joining
plate by using the Wrench (
151
) to tighten two Hex Head Bolts (
112
) , two
Split Washers (
142
) and two Curved Washers (
144
).
2. Connect the Incline Rail Assembly (
3
) with the Main Frame at the rear joining
plate by using the Wrench (
151
) to tighten two Hex Head Bolts (
112
) , two
Split Washers (
142
) and two Curved Washers (
144
).
3. Pull the wire, which is attached to the Computer Cable (
38
), out of
Console Mast (
15
) and secure the mast on the Main Frame by using M8 L
Allen Wrench (
153
) to tighten four Socket Head Cap Bolts (
113
) together
with four Split Washers (
142
) and four Flat Washers (
139
).
4. Plug in the connectors of the Computer Cable (
38
), two Handpulse W/Cable
Assemblies (White & Red) (
44
,
45
), Swing Arm Wire (Upper), Resistance (
48
)
and Swing Arm Wire (Upper), Incline (
49
) on the back of Console Assembly
(
35
) and secure the Console Assembly (
35
) on the console holding plate with
four Phillips Head Screws (
119
) by tightening them with Phillips Head Screw
Driver (
150
).
STABILIZERS
& CONSOLE
MAST
1
See Page 13 for Illustration
2
HARDWARE STEP 2
See Page 13 for Illustration
#112 . 3/8” x 3-3/4” Hex
Head Bolt (4 pcs)
#113
. 3/8” x 3/4”
Socket Head Cap Bolt
(4 pcs)
#119. M5 x 10mm
Phillips Head Screw
(4 pcs)
#139
. 3/8” x 19mm x
1.5T Flat Washer (4 pcs)
#142 . 3/8” x 2T
Split Washer (8 pcs)
#144
. 3/8” x 23 x 2T
Curved Washer (4 pcs)
E25
ASSEMBLY INSTRUCTIONS