Sole Fitness 16013805000 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 33

Sole Fitness 16013805000 Скачать руководство пользователя страница 10

9

[email protected]

Dyaco Canada Inc. 2018

TREADMILL DESK

ASSEMBLY INSTRUCTIONS

!!ATTENTION: IMPORTANT UNPACKING INSTRUCTIONS.
PLEASE READ BEFORE UNPACKING YOUR TREADMILL DESK!!

Serious injury could occur if this treadmill is not unpacked properly. There is a Velcro strap
installed around the treadmill base that prevents the treadmill from unfolding accidentally
during shipping. If this strap is not removed properly the treadmill could spring open
unexpectedly and cause injury if someone is standing near the treadmill when the strap is
removed.

To ensure your personal safety during removal of the shipping strap please make sure the
treadmill is positioned flat on the ground, in the orientation it would be in if you were
using the treadmill. Do not turn the treadmill up on its side while removing the shipping
strap. This could cause the treadmill’s folding mechanism to spring open. If the end of the
Velcro strap (that you need to grab to remove it) happens to be under the treadmill deck,
reach under the deck to grab it, but do not tilt the treadmill up to gain access to the strap
end.

Cut the banding straps with a short box cutter (razor knife); separate the carton from the
one underneath it by prying up on the staples (if applicable). Pull the carton over the
treadmill parts and locate the hardware pack. The hardware pack is separated into five
sections; one section containing tools and four sections labeled steps 1-4 which contain the
hardware needed for assembly of each step. The assembly steps below are numbered one
through four and correspond to the hardware in the numbered sections of the hardware
pack. Remove only the hardware for the step you are currently assembling to avoid
confusion and mix ups.

Then remove the treadmill from the carton and lay it on a level surface.

DESK

ASSEMBLY TOOLS

#

142

. M5 Allen Wrench

#

139

. Phillips Head Screw Driver

#

141

. M6 Allen Wrench

#

140

. 13/14mm Wrench

«
...
8
9
10
11
12
...
»

Содержание 16013805000


































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды