MAN-01-00028-1.1
5
7
Use the three right-most buttons inside the SolarEdge
device (the
UP-1
,
Down-2
and
Enter-3
buttons), shown
above, to type in the following default password:
12312312
.
For firmware versions above 2.250, continue to step
12
.
For earlier versions, complete steps
9
through
11
below.
8
Scroll down to the
Communication
submenu and select it.
9
Select the
Bus
submenu. Scroll down and select
RS485
Slave
. The SolarEdge device performs a reset immediately
after the selection is made.
Bus Submenu:
Z i g b e e P 2 P
Z i g b e e M P
R S 4 8 5 M a s t e r
>
R S 4 8 5 S l a v e
N o n e
10
Repeat steps
6
through
8
above to enter Setup mode.
11
Select the
Server
submenu, scroll down to the
RS485
option and select it. The SolarEdge device performs a reset
immediately after the selection is made.
Communication Submenu:
> S e r v e r < L A N >
B u s < Z i g B e e >
L A N C o n f
R S 4 8 5 C o n f < S >
Z i g b e e C o n f < S >
R S 2 3 2 C o n f
M o d b u s C o n f
This concludes the setting of the slave SolarEdge devices
for firmware versions earlier than 2.250.
Follow steps
12
through
16
for firmware versions
above 2.250.
12
Select the
Server
submenu, scroll down to the
RS485
option and select it.
Communication Submenu:
> S e r v e r < L A N >
L A N C o n f
R S 4 8 5 - 1 C o n f < S >
R S 4 8 5 - 2 C o n f < S >
Z I G B E E C o n f < S >
R S 2 3 2 C o n f
13
Select the
RS485-X Conf
(the port that is physically
connected to the daisy chain)
submenu option.
14
Select the
Device Type
submenu and set it to
SolarEdge
.
RS485-X Submenu:
> D e v i c e T y p e < S E >
P r o t o c o l < M >
D e v i c e I D < 1 >
S l a v e D e t e c t
15
Select the
Protocol
submenu and set it to
Slave
.
16
Press the
ESC
button repeatedly to exit the Setup menu or
wait for the device to automatically exit Setup mode if no
buttons are pressed for more than two minutes.
This concludes the slave device configuration using the
LCD button for firmware version 2.250 and above.
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
For the master (main) SolarEdge device, perform the
following steps:
1
Repeat steps
2
through
8
, as described above in the Slave
Configuration section to enter Setup mode.
For firmware versions above 2.250, continue to step
7
.
For earlier versions, complete steps
2
through
6
below.
2
Select the
Bus
submenu. Scroll down and select
RS485
Master
. The SolarEdge device performs a reset
immediately after the selection is made.
Bus Submenu:
Z i g b e e P 2 P
Z i g b e e M P
> R S 4 8 5 M a s t e r
R S 4 8 5 S l a v e
N o n e
3
Repeat steps
6
through
8
above in the Slave
Configuration section to enter Setup mode.
4
Scroll down to the
RS485 Conf
submenu and select it.
Select the
Master Set
option and select
Enable
. The
SolarEdge device performs a reset immediately after the
selection is made.
Communication Submenu:
S e r v e r < L A N >
B u s < Z i g B e e >
L A N C o n f
> R S 4 8 5 C o n f < S >
Z i g b e e C o n f < S >
R S 2 3 2 C o n f
M o d b u s C o n f
5
Repeat steps
6
through
8
as described above in the
Slave Configuration section to enter Setup mode.
6
Scroll down to the
RS485 Conf
submenu and select
it.
Communication Submenu:
S e r v e r < L A N >
B u s < Z i g B e e >
L A N C o n f
> R S 4 8 5 C o n f < S >
Z i g b e e C o n f < S >
R S 2 3 2 C o n f
M o d b u s C o n f
