background image

SOLAHART STREAMLINE DIRECT OPEN CIRCUIT 

SOLAR WATER HEATER WARRANTY – AUSTRALIA ONLY 

54 

SOLAR STREAMLINE DIRECT WATER HEATER MODELS 270MDV, 320MDV, 410MDV 

 

3.

 

WHAT IS COVERED BY THE SOLAHART WARRANTY 

FOR THE WATER HEATERS DETAILED IN THIS DOCUMENT 

3.1

 

Solahart will repair or replace a faulty component of your water heater if it fails to operate in accordance with its specifications as 
follows: 

 

What components are covered 

The period from the date of 

installation in which the fault must 

appear in order to be covered 

What coverage you receive  

All 

components 

(all installations) 

Year 1  

Repair  and / or  replacement  of  the  faulty 
component, free of charge, including labour. 

All 

components 

(only if the water heater is installed in 

a single-family domestic dwelling)

 

Year 2 

Repair  and / or  replacement  of  the  faulty 
component, free of charge, including labour. 

The cylinder and solar collector 

(if the water heater is installed in 

a single-family domestic dwelling) 

Year 3 

Repair  and / or  replacement  of  the  cylinder  or 
solar collector, free of charge, including labour. 

Years 4 & 5 

Replacement  cylinder  or  solar  collector,  free  of 
charge.  Installation  and  repair  labour  costs  are 
the responsibility of the owner. 

The cylinder 

(if the water heater is not installed in 

a single-family domestic dwelling) 

Years 2 & 3 

Replacement cylinder, free of charge. Installation 
and  repair  labour  costs  are  the  responsibility  of 
the owner. 

 

 

4.

 

ENTITLEMENT TO MAKE A CLAIM UNDER THIS WARRANTY 

4.1

 

To be entitled to make a claim under this warranty you need to:  
a)

 

Be the owner of the water heater or have consent of the owner to act on their behalf. 

b)

 

Contact Solahart without undue delay after detection of the defect and, in any event, within the applicable warranty period. 

4.2

 

You are not entitled to make a claim under this warranty if your water heater: 
a)

 

Does not have its original serial numbers or rating labels. 

b)

 

Is not installed in Australia. 

 

5.

 

HOW TO MAKE A CLAIM UNDER THIS WARRANTY 

5.1

 

If you wish to make a claim under this warranty, you need to: 
a)

 

Contact  Solahart  on  1800  638  011  and  provide  owner’s  details,  address  of  the  water  heater,  a  contact  number  and  date  of 

installation of the water heater or if that’s unavailable, the date of manufacture and serial number (from the rating label on the 
water heater). 

b)

 

Solahart will arrange for the water heater to be tested and assessed on-site. 

c)

 

If Solahart determines that you have a valid warranty claim, Solahart will repair or replace the water heater in accordance with this 
warranty. 

5.2

 

Any expenses incurred in the making of a claim under this warranty will be borne by you. 

 

6.

 

THE AUSTRALIAN CONSUMER LAW 

6.1

 

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or 
refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have 
the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. 

6.2

 

The Solahart warranty (set out above) is in addition to any rights and remedies that you may have under the Australian Consumer 
Law. 

 
 

Содержание Streamline 270MDV

























































Отзывы: