manualshive.com logo in svg

Solahart 325 HAV, Руководство пользователя

Поделиться
Скачать
Solahart 325 HAV Скачать руководство пользователя страница 28

HEAT PUMP AND TANK ASSEMBLY 

28 

ASSEMBLY PROCEDURE 

  Warning:

  The  heat  pump  must  be  assembled,  plumbed  and  filled  with  water  prior  to  power  being 

connected and switched on. 
 
The following procedure should be followed to properly place the heat pump module in position and connect 
to the storage tank: 

1. 

Heat  Pump  Storage  Tank:

  Remove  all  packaging  including  the  carton  base  from  the  heat  pump 

storage tank and position in its intended location, supported by a level slab or solid base. 

The water connections may be on either the left or right hand side and should be parallel to the wall. 

The storage tank must be positioned at least 100 mm from the wall. If a minimum clearance of 100 mm 
is not allowed for, the heat pump module will not be able to be completely connected to the storage tank. 

The storage tank must also be positioned such that when the heat pump module is in position, there is a 
clearance  of  at  least  300 mm  perpendicular  from  both  the  front  air  inlet  louvres  and  the  outlet  grille  to 
any wall or obstruction. 

638

574

   3

00 

MIN

   3

00 

MI

N

32°

613

894

281

AIR

OUTLET

AIR INLET

VENTILATION

CLEARANCE

CONDENSATE
DRAIN

AIR

INLET

TPR

VALVE

1631

1317

119

162

544

872

1018

ELECTRICAL
CONNECTION

AIR

OUTLET

AIR INLET

  3

00

 M

IN

COLD

INLET

HOT

OUTLET

VENTILATION

CLEARANCE

100

 

 

Step 1 

position storage tank at least 100 mm from the wall 

and allow for at least 300 mm ventilation clearance 

 

2. 

Protective Film:

 Peel away and completely remove the protective film cover from the jacket and jacket 

top of the storage tank. 

 

Ensure  the  two  plastic  caps  on  the  jacket  top  remain  firmly  fitted  in  position  and  the  removal 
process does not loosen or dislodge them. 

 

Ensure there are no remnants of the protective film left around or under caps, seals and fittings. 

The  function  of  the  protective  film  is  to  protect  the  jacket  and  jacket  top  of  the  storage  tank  against 
scratching  and  scuffing  during  transport  and  handling.  It  is  not  intended  or  suitable  for  long  term 
exposure to the weather and is not to be left on the water heater jacket and jacket top. 

 

Содержание 325 HAV

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды