SNOWJOE iON24SB-XRP-RM, Руководство оператора

Страница: 17 / 28

16
Stopping the Machine
1. Release both drive trigger and auger trigger. Drive motor
and auger will stop (Fig. 26).
2. Wait for all moving parts to come to a complete stop.
3. Disengage safety switch.
4. Turn power switch to OFF position and remove key.
Operating Tips
m
WARNING!
Foreign objects, such as rocks, broken
glass, nails, wire, or string, can be picked up and thrown by
the snow blower, causing serious personal injury. Remove all
foreign objects from the area to be plowed before operating
the snow blower.
Snow is best removed as soon as possible after snow fall.
1. Keep the area of operation free of foreign objects that can
become thrown by the rotor blades. Perform a thorough
inspection of the area since some objects may be hidden
from view by surrounding snow. If the snow blower hits an
obstruction or picks up a foreign object during use,
stop the snow blower, remove the key and batteries ,
remove the obstruction, and inspect the unit for damage.
Repair or replace any damaged part before restarting and
operating the unit.
2. Keep children, pets, and bystanders away from the area of
operation. Be aware that the normal noise of the machine
when turned on may make it difficult for you to hear
approaching people.
3. To clear an area, run unit in an overlapping series of paths.
Fot large areas, start in the middle and throw snow to
each side, so snow is not cleared more than once.
4. Note the wind direction. If possible, move in the same
direction as the wind so that the snow is not thrown
against the wind (and thus back into your face and on the
just cleared path).
5. Do not push the snow blower with excessive force. Do not
exceed the unit's intake or throw rate.
6. Some parts of the snow blower may freeze under extreme
temperature conditions. Do not attempt to operate the
snow blower with frozen parts. If the parts freeze while
the snow blower is in use, stop the snow blower , remove
the batteries , and inspect for frozen parts. Free all parts
before restarting or operating the snow blower. Never
force controls that have frozen.
Traveling
To travel from one work area to another:
1. Press down on handle grips enough to raise front of unit
slightly off surface.
2. Engage drive trigger without engaging auger trigger.
Maintenance
To order genuine replacement parts or accessories for the
Snow Joe
®
iON24SB-XRP cordless snow blower, please visit
snowjoe.com or contact the Snow Joe
®
+ Sun Joe
®
customer
service center at 1-866-SNOWJOE (1-866-766-9563).
m
WARNING!
Make sure to turn off the switch and
remove the key and batteries before performing any
maintenance task on your snow blower.
General Maintenance Tips
1. Do not attempt to repair the machine unless you have the
proper tools and instructions for disassembly and repair of
the machine.
2. Check bolts and screws at frequent intervals for proper
tightness to ensure that the equipment is in safe working
condition.
3. After each snow removal session, run the snow blower
for a few minutes to prevent the collector/impeller from
freezing. Shut off the motor, wait for all revolving parts
to stop completely, remove key and batteries and wipe
residual ice and snow off the unit. Rotate the chute
deflector by the rotating the chute crank several times to
remove any excess snow.
Proper Care for B Charger
m
WARNING!
To reduce the risk of injury, always unplug
the charger and remove the battery pack from the charger
before performing any maintenance task. Never disassemble
the battery pack or charger. Contact your Snow Joe
®
+
Sun Joe
®
dealer or the Snow Joe
®
+ Sun Joe
®
customer
service center for ALL repairs.
1. To reduce the risk of injury and damage, never immerse
your battery packs or charger in liquid or allow any liquid
to flow inside these components.
2. Clean out dust and debris from charger vents and
electrical contacts by blowing with compressed air.
Fig. 26
Drive Trigger
(Left-handle)
Auger trigger
(Right-handle)
Safety key/
Power switch
Safety
switch