background image

9

NOTE: If the charge level button does not appear to be 

working, place the battery pack on the charger and charge as 

needed.
NOTE:

 Immediately after using the battery packs, the charge 

level button may display a lower charge than it will if checked 

a few minutes later. The battery cells “recover” some of their 

charge after resting.

Charger Operation

m

WARNING!

 Charge only iON+ 24V lithium-ion battery

packs with their compatible iON+ 24V lithium-ion charger. 

Other types of batteries may cause personal injury and 

damage.

To reduce the risk of electric shock, do not allow water to flow 

into the charger's AC/DC plug.

When to Charge the iON+ 24VBAT 

Lithium-iON Batteries

NOTE: The iON+ 24VBAT lithium-ion battery packs do 

not develop a "memory" when charged after only a partial 

discharge. Therefore, it is not necessary to run down the 

battery packs before charging. 

• Use the battery indicator lights to determine when to charge

your iON+ 24VBAT lithium-ion battery packs.

• You can "top-off" your battery pack's charge before starting

a big job or after a long day of use.

Charging the Batteries

1.

Open the battery compartment cover to expose the

batteries. Press the push lock buttons on the batteries to

pull them out of the equipment (Fig. 1).

2. Check that the mains voltage is the same as that marked

on the rating plate of the battery charger. Then, insert the

charger's plug into the electrical wall outlet. When you

plug in the charger, two green lights will illuminate and

stay green (Fig. 2).

3. Place the battery packs into the charger by sliding the

packs to lock them into position. When you insert the

batteries into the charger, the two green lights will go

off, and the red lights will 

illuminate to indicate that the

batteries are charging (Fig. 3).

4.

When the charger lights turn green, the batteries are fully

charged (Fig. 3).
NOTE: 

A fully discharged pack with an internal

temperature in the normal range will fully charge in

1 hr 50 mins (between 32ºF/0ºC and 113ºF/45ºC).

5. If th

e light indicators do not come on at all, check that

the battery packs are fully seated into the bay. Remove

the battery packs and reinsert. If the problem persists,

contact an authorized Snow Joe

®

 + Sun Joe

®

 dealer or

call the Snow Joe

®

 + Sun Joe

®

 customer service center at

1-866-SNOWJOE (1-866-766-9563) for assistance.

6.

When charging is complete, remove the batter

ies from the

charger (Fig. 4).

Fig. 1

Battery packs

Battery compartment 

cover

Fig. 2

Charger

green

Power on

Fig. 3

Battery packs

red

Charging

green

Fully 

Charged

Содержание 24V-X2-SB18U



















Отзывы: