background image

© Trynex International 2008        L1186

8 — 33

Useful Formulas 

Material Type

Equipment installed when vehicle

was weighed

Front Gross Axle Weight Rating

(RGAWR)

Rear Vehicle Weight Rating

(GVWR) (lb.)

Gross Vehicle Weight (GVW) (lb.) (empty)

Payload Available (lb.)

Material Weight (lb./cu. yd.)

Maximum Volume (cu. yd.)

Maximum Height (approximate) (in.)

Loaded Front Gross Axle Weight

(FGAW) (lb.)

Loaded Rear Gross Axle Weight

(RGAW) (lb.)

Loaded Gross Vehicle Weight (GVW) (lb.)

Example:

Coarse Salt – Dry

6'/8' Vee Pro

8600

–  6500

=  2100

÷

  1431

=  1.47

24"

– 

÷

 

– 

÷

 

– 

÷

 

– 

÷

 

Determining Vehicle Payload

Torque Chart

When tightening fasteners, refer to the Torque Chart below for 

the recommended fastener torque values.

These torque values apply to mount assembly fasteners except

those noted in the instruction.

Recommended Fastener Torque Chart (ft.-lb.)

1/4-20

5/16-18

3/8-16

3/8-24

7/16-14

1/2-13

9/16-12

5/8-11

3/4-10

7/8-9

1-8

SIZE

SAE

Grade 8

6

11

19

24

30

45

66

93

150

202

300

9

18

31

46

50

75

110

150

250

378

583

13

28

46

68

75

115

165

225

370

591

893

SAE

Grade 5

SAE

Grade 2

Metric Grade 8.8 (ft.-lb.)

SIZE

TORQUE

SIZE

TORQUE

M 6

M 8

M 10

7

17

35

M 12

M 14

M 16

60

95

155

Material Weights

Refer to the table below for the weight per cubic yard 

of common spreading materials.

Fine Salt – Dry

Coarse Salt – Dry

Sand/Salt Mix – Dry (50/50)

Cinders

MATERIAL

2,025

1,431

2,700

1,080

WEIGHT 

(lb. per cubic yard)

SP-2400

Содержание SP-2400





































Отзывы: