background image

8

16992210 Rev A

Your plow is now ready for operation. The hydraulic system has been filled at the factory and should be fully 
operational. It is possible that agitation due to the shipping has introduced some air into the oil. When operating 
the plow for the first time some oil may exit the vent (by the coils). This should stop once the plow is cycled 
and operational. Check all plow and light functions. If something is not working correctly, reread the installation 
directions to make sure a step was not missed and check the schematics.

STORAGE

1.

 Before disconnecting the plow from your vehicle, fully compress the lift cylinder

2.

 Disconnect the plow from your vehicle

3.

 Coat all electrical connection points with dielectric grease

4.

 Repair/touch up any chipped paint or rusted areas

5.

 Apply a coat of oil or grease to all exposed chrome (on angle and lift cylinders)

6.

 Grease all grease fittings on trip pins and king pin

REMOVAL FROM STORAGE

1.

 Check all fasteners and hydraulic fittings for tightness.

2.

 Replace any cracked hydraulic hoses

3.

 Coat all electrical connection points with dielectric grease

4.

 Connect plow to vehicle

MAINTENANCE

The SnowDogg line of plows has been simply designed for reliable service. In order to ensure the reliability of 
your plow, observe the following maintenance items and regularly inspect:
• Fasteners and retaining devices for proper installation and tightness.
• Hydraulic cylinders for damage, pitting or leakage
• Hydraulic hoses for wear, damage or leakage. Replace any damaged hose.
• All electrical connections for corrosion – apply dielectric grease as required
• Cutting edge wear
• Plow shoe wear
• Greasable fittings (2x trip pins and king pin)

HYDRAULIC SYSTEM

•  All SnowDogg plows use SnowDogg brand Low-Temperature Hydraulic Fluid (P/N 16150010) available from 

SnowDogg dealers.

• The reservoir should be filled through to top port until oil reaches the top port.
•  Recheck and tighten all fittings and valves every season or as necessary. Vibration due to normal use can 

cause fittings to loosen.

•  Loctite or Teflon tape should not be used on any fittings or hoses. The only plugs where pipe sealant may be 

used are the reservoir plugs.

•  The reservoir should be drained and refilled every season to ensure that the oil remains free of water and 

contanimants. If contaminants are known to be present, it is recommended that the reservoir be removed and 
cleaned.

With proper maintenance and care your SnowDogg plow will provide years of trouble free service!

 

Содержание MUT Series

















Отзывы: