background image

3

This manual was written for the assembly, installation and
maintenance of your new Sno-Way ProControl 2 Plus™
Operating System. Most importantly, this manual provides
an operating plan for safe use. Refer to the Table of
Contents for an outline of this manual.
Please keep this manual with your machine at all times as
reference material and so it can be passed on to the next
owner if the machine is sold.
We require that you read and understand the contents of
this manual COMPLETELY, especially the chapter on
SAFETY, before attempting any procedure contained in
this manual.

The Society of Automotive Engineers has adopted
this SAFETY ALERT SYMBOL to pinpoint character-
istics that, if NOT carefully followed, can create a
safety hazard. When you see this symbol in this man-
ual or on the machine itself, BE ALERT!, your per-
sonal safety and the safety of others, is involved.

• Defined below are the SAFETY ALERT messages 

and how they will appear in this manual.

NOTE: Additional information concerning the equipment 
or the procedure that may or may not be contained else-
where in this manual.

BE AWARE! It is illegal to remove, deface or other-
wise alter the safety decals mounted on this equip-
ment.

Record the ProControl 2 Plus™ transmitter and Receiver
Serial Numbers. This is information that your Dealer
needs to answer questions or to order replacement parts,
if needed, for your unit.

We reserve the right to make changes or improve the 
design or construction of any part(s) without incurring the 
obligation to install such parts or make any changes on 
any unit previously delivered.

Graphics and illustrations may be used which may show 
equipment and/or options not included in every 
installation without incurring the obligation to install such 
parts or make changes on units previously delivered.

Sno-Way Service Parts Manuals are available on-line or 
at your authorized Sno-Way dealer. For U.S. models, 
request part number 97101915 for the Controller. For U.K. 
models, request part number 97102149 for the Controller.

Factory contact information is available at 
www.snoway.com.

WARNING

INDICATES A HAZARDOUS SITUATION WHICH, 
IF NOT AVOIDED, COULD RESULT IN DEATH 
OR SERIOUS INJURY.

CAUTION

INDICATES A HAZARDOUS SITUATION WHICH,
IF NOT AVOIDED, COULD RESULT IN MINOR
OR MODERATE INJURY.

NOTICE

IS USED TO ADDRESS PRACTICES NOT
RELATED TO PHYSICAL INJURY. FAILURE TO
FOLLOW COULD LEAD TO PROPERTY
DAMAGE.

DEALER

NAME

PHONE (     ) –

ADDRESS

CITY

STATE

ZIP

(FILL IN)

ORIGINAL PURCHASER

NAME

PHONE (      ) –

ADDRESS

CITY

STATE

ZIP

(FILL IN)

NAME DECAL DATA

(FILL IN)

PROCONTROL 2 PLUS

TM

 SERIAL NUMBERS:

TRANSMITTER S.N.

RECEIVER S.N.

RECEIVER S.N.
(SPREADER)

(PLOW)

RECEIVER S.N.
(VEHICLE)

INTRODUCTION

Содержание 99101398

















Отзывы: