manualshive.com logo in svg

Sno-Way 99101398, Инструкция по установке и эксплуатации, Страница: 14 / 16

Поделиться
Скачать
Sno-Way 99101398 Скачать руководство пользователя страница 14

14

ProControl 2 Plus™ Transmitter
Mounting Instructions

Your ProControl 2 Plus™ transmitter comes with a cradle
for mounting the transmitter on the dash.

Fasten the cradle in the desired location using the 2 screw
holes. (See Figure 1-17).

NOTE: Be certain control mounting does not obstruct 
items that are critical to safely operating your vehicle.

Figure  1-17

Using the ProControl 2 Plus™ to Aid in 
Mounting and Removing the Snow Plow

The ProControl 2 Plus™ transmitter can be used near the
snow plow when mounting or removing the plow with the
aid of the power jackstand. 

NOTE: For proper procedure in mounting and removal of 
the snow plow, refer to your Sno-Way Plow Owner’s Man-
ual.

Disconnect the cable for the ProControl 2 Plus™
transmitter at the harness connection inside the vehicle
cab and take the controller to the front of the vehicle.
Disconnect the plow control harness from the vehicle
control harness at the connector at the front of the vehicle.
Connect the ProControl 2 Plus™ transmitter to the plow
control harness. The ProControl 2 Plus™ transmitter can
now be used just as it is normally used in the cab of the
vehicle.

When plow mounting or removal is completed, reconnect
the ProControl 2 Plus™ transmitter to the vehicle harness
connector in the cab. Connect plow harness to truck
harness or place protective caps on truck and plow
harnesses.

Storage

Your receiver module is equipped with male and female
connectors. When power is no longer connected to the
plow, plug the male into the female connector for storage. 

Your vehicle harness is also equipped with male and
female connectors. Once the plow is disconnected, plug
the male into the female connector for storage.

Wiring Schematics

ProControl 2 Plus™ system schematic diagrams are
located in your products Installation & Owner’s Manual.

VEHICLE RECEIVER

LIGHT

INDICATION

DESCRIPTION

GREEN FLASHING 

LED

PLOW TRANSMITTER ON 

AND CONNECTED WITH 

PLOW RECEIVER

SOLID GREEN LED

SENSING A MARKER, 

TURN, LOW BEAM, HIGH 

BEAM, OR DRL SIGNAL, 

AND PLOW RECEIVER 

ATTACHED AND 

POWERED, BUT PLOW 

TRANSMITTER IS OFF

SOLID RED LED

SENSING A MARKER, 

TURN, LOW BEAM, HIGH 

BEAM, OR DRL SIGNAL, 

BUT NO PLOW RECEIVER 

ATTACHED AND 

POWERED

RED FLASHING LED

PLOW TRANSMITTER IS 

OFF AND NO MARKER, 

TURN, LOW BEAM, HIGH 

BEAM, OR DRL IS SENSED

MOUNTING

SCREW

LOCATIONS

WARNING

When using the ProControl 2 Plus

™ 

transmitter

near the plow, be especially careful of the
movement of any plow components when any
switch on the transmitter is actuated. Stand
clear of the snow plow at all times to avoid
being struck by any plow parts.

INDICATES A HAZARDOUS SITUATION WHICH, 
IF NOT AVOIDED, COULD RESULT IN DEATH 
OR SERIOUS INJURY.

Содержание 99101398

















Отзывы:

Нет отзывов