manualshive.com logo in svg

Snell IQOTR40, Руководство пользователя, Страница: 6 / 28

Поделиться
Скачать
Snell IQOTR40 Скачать руководство пользователя страница 6

IQOTR40/41/42/43/44/45/99 

www.snellgroup.com

 

 

Technical Profile 

Inputs and Outputs 

Signal Inputs (Tx) 

Electrical  

3 Gbps HD-SDI, 1.485 Gbps HD-SDI or 270 Mbps SD-SDI (asynchronous 
operation available at other frequencies) 

Connector / format  

BNC / 75 Ohm, DIN1.0/2.3, HDBNC panel jack 

Conforms to  

SMPTE 424M (HD level A) 

SMPTE 292M (HD) 

SMPTE 259M-C (SD) 

Inputs  

4 

Input cable length  

Up to 100m Belden 1694A @ 3Gbps 

Up to 150m Belden 1694A @ 1.5 Gbps 

Up to 250m Belden 1694A @ 270 Mbps 

Signal Inputs (Rx) 

Optical  

3 Gbps HD-SDI, 1.485 Gbps HD-SDI or 270 Mbps SD-SDI (asynchronous 
operation available at other frequencies) 

Connector / format  

LC single mode SFP 

Conforms to:  

SMPTE 297-2006 

Inputs  

4 

 

Signal Outputs (Tx) 

Optical  

3 Gbps HD-SDI, 1.485 Gbps HD-SDI or 270 Mbps SD-SDI (asynchronous 
operation available at other frequencies) 

Connector / format  

LC single mode SFP 

Conforms to  

SMPTE 297-2006 

Outputs  

1 to 4 per Channel 

Signal Outputs (Rx) 

Electrical  

3 Gbps HD-SDI, 1.485 Gbps HD-SDI or 270 Mbps SD-SDI (asynchronous 
operation available at other frequencies) 

Connector / format  

BNC / 75 ohm, DIN1.0/2.3, HDBNC panel jack 

Conforms to  

SMPTE 424M (HD level A) 

SMPTE 292M (HD) 

SMPTE 259M-C (SD) 

Outputs  

1 to 4 per Channel 

 

Controls 

Indicators 

Power OK 

(Green) 

CPU 

OK (Green flashing) 

Good 

Hardware OK (Green) 

Warning 

SFP fit not as sold (Yellow), SFP warning active (Yellow flashing), OK (Off) 

Error 

Hardware error (Red), SFP alarm active (Red flashing), OK (Off) 

Input 1-8 

SD-OK (Yellow), HD-OK (Green), 3G-OK (Blue), other-OK (White flashing), 
Bypass (Rate colour flashing), Loss (Red) 

Issue 1 Rev 2 

 

© 2012 Snell Limited 

Page 6

Содержание IQOTR40





























Отзывы:

Нет отзывов