background image

 

 

Section 2 - OPERATING INSTRUCTIONS 

 

WARNING 

DO NOT attempt any maintenance, adjustments or 
service with engine and blade running. STOP engine 
and blade. Disconnect spark plug wire and secure 
away from spark plug. Engine and components are 
HOT. Avoid serious burns, allow sufficient time for 
all components to cool. 

 
2.6 RECYCLING 

OPERATION 

NOTE: For best recycling results, cut up to a maximum 
of 1/3 of grass blade length and recycle ONLY when 
grass is dry. 

1.  Set all wheels in the highest cutting position 
(Notch 6). 
2.  Move engine speed control to “FAST” (Rabbit) 
position. 
3. Move ground speed control to slowest speed 
setting. 
4.  Proceed mowing slowly. If grass is very dense, 
lower each rear wheel latch one notch lower than 
the front wheel latches to improve recycling 
performance. 

 
INSTALLATION of GRASS BAG ADAPTER 
(Optional Accessory on Some Models) 
STEP 1:
 Install the grass bag adapter and secure to the 
side and top of the deck with the two nuts provided with 
the machine. Slot in front edge of adapter must be under 
nut located on top of deck. See Figure 2.7. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

FIGURE 2.7 

 
 
 
 
 
 

INSTALLATION of RECYCLING PLUG 
(Optional Accessory on Some Models) 
STEP 1:
 Once adapter has been installed, recycling may 
be desired. Insert recycling plug completely and securely 
into adapter. Install grass bag. See Figure 2.8. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

FIGURE 2.8 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

WARNING 

DO NOT operate without entire Grass Bag or guard 
in place. Grass Bag components are subject to 
deterioration during normal use. Inspect frequently 
and replace worn or damaged components 
immediately. 

 
 

SECURE ADAPTER 
TO DECK WITH NUTS 

SECURE 
WITH NUTS 

ADAPTER 

INSERT RECYCLING PLUG 
COMPLETELY AND SECURELY 
INTO ADAPTER. INSTALL 
GRASS BAG. 

ADAPTER 

PLUG 

Содержание WMRP216517B





























Отзывы: