Snapper RP2167519BDV Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 28

Snapper RP2167519BDV Скачать руководство пользователя страница 16

16

Section 4 - REPAIR & ADJUSTMENTS

WARNING

DO NOT attempt any maintenance, adjustments or
service with engine and blade running. STOP engine
and blade. Disconnect spark plug wire and secure
away from spark plug. Engine and components are
HOT. Avoid serious burns, allow sufficient time for
all components to cool.

4.3.3. DRIVEN DISC ADJUSTMENT

(Continued From Previous Page)

2.

Remove driven disc spring from driven disc

assembly. Also remove pin and washer from transfer
rod, and remove end of transfer rod from hole in
driven disc assembly. See Figure 4.9.

FIGURE 4.9

3.

Slide driven disc assembly over to 1/8” from

outside edge of drive disc. See Figure 4.10.

4.

Loosen jam nut securing transfer rod to ball joint

on pivot bracket. See Figure 4.11.

5.

Turn rod in or out of ball joint until end of rod aligns

with hole in driven disc assembly from which rod was
removed. NOTE: Do not move pivot bracket.

6.

Reinstall rod as removed in step 2. Move ground

speed control to ‘slow’ position, then back to ‘fast’
position. Recheck the 1/8” measurement described
previously. Readjust as needed. Tighten nut when
finished.

7.

Reinstall driven disc spring to driven disc

assembly.

FIGURE 4.10

FIGURE 4.11

(Continued On Next Page)

4.3.4. Replacing Rubber Driven Disc

If the rubber is badly chunked or worn it must be
replaced. Install new Driven Disc as follows:

1.

Remove pin and washer from transfer rod, and

remove end of transfer rod from hole in driven disc
assembly. See Figure 4.9.

DRIVEN DISC
ASSEMBLY

DRIVE
DISC

REMOVE
DRIVEN DISC
SPRING

REMOVE END
OF TRANSFER
ROD FROM
DRIVEN DISC
ASSY

BALL JOINT

TURN ROD IN
OR OUT UNTIL
END ALIGNS
WITH HOLE

PIVOT
BRACKET

1/8” MEASUREMENT TO
OUTSIDE EDGE OF DRIVE
DISC

DRIVE
DISC

SLIDE DRIVEN
DISC ASSEMBLY
TOWARD OUTSIDE
EDGE

OUTSIDE
EDGE

REMOVE
PIN AND
WASHER
FROM ROD

LOOSEN NUT

«
...
14
15
16
17
18
...
»

Содержание RP2167519BDV





























Отзывы:

Нет отзывов