background image

 

10

Section 2 - OPERATING INSTRUCTIONS 

 

WARNING 

DO NOT attempt any maintenance, adjustments or 
service with engine and blade running. STOP 
engine and blade. Disconnect spark plug wire and 
secure away from spark plug. Engine and 
components are HOT. Avoid serious burns, allow 
sufficient time for all components to cool. 

 
2.8  INSTALLATION OF GRASS BAG ADAPTER 
(Optional Accessory on Some Models) 
STEP 1:

 Remove recycling cover. Refer to Section 

“Recycling Operation”.   

STEP 2:

 Install grass bag adapter to the deck in place of 

recycling cover, making sure that: 1) hole on outside front 
of adapter fits onto stud in front of discharge opening 
where front of recycling cover was originally installed, 2) 
slot on top of adapter slips under restraining nut on top of 
deck (under right front corner of engine), and 3) slot on 
bottom rear of adapter slips onto stud behind rear of 
discharge opening, where rear of recycling cover was 
originally secured. See Figure 2.10. Install 
internal/external tooth lock washers and knob nuts on 
studs and tighten securely. 

STEP 3:

 Route recoil rope around outside of rope guide 

pulley. See Figure 2.10. (NOTE: Recoil rope may need to 
be slackened.  Refer to “Handle Assembly”.) 

 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

FIGURE 2.10 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

2.9  INSTALLATION OF GRASS BAG 
 

(Door Type Bag) 
STEP 1:

 Install grass bag adapter. Refer to Section 

“Installation of Grass Bag Adapter”. 

STEP 2:

 Install grass bag by sliding connector over 

adapter flange. See Figure 2.11. 

STEP 3:

 Attach grass bag hooks over middle handle 

cross bar. See Figure 2.11. 

 
 

 

 

FIGURE 2.11 

 

 

WARNING 

DO NOT operate without entire Grass Catcher or 
guard in place. Grass Catcher components are 
subject to deterioration during normal use. Inspect 
frequently and replace worn or damaged 
components immediately. 

 

WARNING 

Grass Catcher bags used on SNAPPER products 
are made of woven fabric, and are subject to 
deterioration and wear during normal usage. 

 

Check condition of bag before each use. 

 

Immediately replace worn or damaged catcher bags 
with only bags recommended by SNAPPER.  The 
grass catcher is optional equipment on some 
models. 

ROUTE RECOIL ROPE 
AROUND PULLEY 

HOOK TO MIDDLE 
HANDLE CROSS BAR 

SLIDE 
CONNECTOR 
OVER FLANGE 

SECURE 
ADAPTER 
TO DECK 

Содержание RP2167519BDV





























Отзывы: