Snapper 21” STEEL DECK “M” WALK BEHIND MOWER Set-up Скачать руководство пользователя

Страница: 3 / 4

STEP 8: Driven disc to drive disc adjustment is set up at
the factory. In case driven disc may need adjustment,
proceed as follows:

A. Place speed control rod in the number six speed
position. See Figure 7.

FIGURE 7

B. Remove driven disc spring from driven disc
assembly as shown. Loosen connector hex-nut. See
Figure 8.

FIGURE 8

C. Slide driven disc assembly over until 1/8” from
outside edge of drive disc. Maintaining the 1/8”
measurement, remove any looseness from the linkage.
This can be done by holding the transfer rod and
applying pressure to the left (as viewed from operators
position), then retighten the connector hex nut
securely. See Figure 9. Move shift rod to the number
one speed position, then back to the number six speed
position. Recheck the 1/8” measurement described
previously. Reinstall driven disc spring to driven disc
assembly.

FIGURE 9

STEP 9: Make sure all nuts and bolts are tight. Set-up is
now complete for self-propelled models Proceed to the
pre-sale checklist page of this instruction to prepare
mower for use.

MOVE GROUND SPEED
CONTROL TO SIX SPEED
POSITION

SIXTH SPEED
POSITION

SIXTH

FIRST SPEED
POSITION

FIRST

DRIVEN DISC
ASSEMBLY

DRIVE DISC

DRIVEN
DISC
SPRING

TRANSFER
ROD

CONNECTOR

CONNECTOR HEX
NUT

1/8” MEASUREMENT
TO OUTSIDE EDGE
OF DRIVE DISC

SLIDE DRIVEN
DISC ASSEMBLY
TOWARD
OUTSIDE EDGE

CONNECTOR

TRANSFER
ROD

CONNECTOR
HEX NUT

OUTSIDE
EDGE

DRIVE
DISC

Содержание 21” STEEL DECK “M” WALK BEHIND MOWER Set-up

Страница 1: ...per handle T Knobs on both sides See Figure 2 FIGURE 2 STEP 3 Raise upper and lower handle until it seats into position in the lower handle brackets Securely tighten lower handle T Knobs on both sides See Figure 3 FIGURE 3 IMPORTANT DO NOT tip machine with carburetor or spark plug down Oil from crankcase will saturate the air filter and cause the engine to be hard to start or not start at all If c...

Страница 2: ... clutch cable and clutch spring NOTE Clearance between spring and cable is very important Excessive clearance will cause drive system NOT to operate when wheel drive control handle is depressed No clearance at all will cause mower to continue to propel itself when wheel drive control handle is released to stop mower movement Slide vinyl spring cover located at the end of clutch cable up clutch cab...

Страница 3: ...retighten the connector hex nut securely See Figure 9 Move shift rod to the number one speed position then back to the number six speed position Recheck the 1 8 measurement described previously Reinstall driven disc spring to driven disc assembly FIGURE 9 STEP 9 Make sure all nuts and bolts are tight Set up is now complete for self propelled models Proceed to the pre sale checklist page of this in...

Страница 4: ...e when released DEALER S RECORDS FINAL CHECK _____ PERSONALLY HANDED Operator s Manual Mower Safety Booklet to purchaser _____ INSTRUCTED purchaser to read and follow instructions in Operator s Manual _____ DEMONSTRATED proper starting procedure and operation of mower to purchaser _____ INSTRUCTED purchaser how to service air cleaner maintain oil level 4 cycle _____ ASSISTED purchaser in completin...

Результаты поиска

Содержание 21” STEEL DECK “M” WALK BEHIND MOWER Set-up

Отзывы:

Похожие инструкции для 21” STEEL DECK “M” WALK BEHIND MOWER Set-up

Бренды по названию

Популярные бренды

Snapper 21” STEEL DECK “M” WALK BEHIND MOWER Set-up, Инструкции

Результаты поиска

Содержание 21” STEEL DECK “M” WALK BEHIND MOWER Set-up

Отзывы:

Похожие инструкции для 21” STEEL DECK “M” WALK BEHIND MOWER Set-up

Бренды по названию

Популярные бренды