background image

2

Safety Rules
& Information

Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of
unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The trian-
gle         in text signifies important cautions or warnings which must be followed.

SAFETY DECALS

This unit has been designed and manufactured to pro-
vide you with the safety and reliability you would expect
from an industry leader in outdoor power equipment
manufacturing.

Although reading this manual and the safety instructions
it contains will provide you with the necessary basic
knowledge to operate this equipment safely and effec-
tively, we have placed several safety labels on the unit to
remind you of this important information while you are
operating your unit.

All  DANGER,  WARNING,  CAUTION  and instructional
messages on your rider, attachments and mower should
be carefully read and obeyed. Personal bodily injury can
result when these instructions are not followed. The
information is for your safety and it is important!  The
safety decals below are on your product.

If any decals are lost or damaged, replace them at once.
See your local dealer for replacements.

• Know the unit’s controls and how to stop quickly.

READ THE OPERATOR’S MANUALS.

• Read and obey all safety decals.
• Only allow responsible adults, who are familiar with

the instructions, to operate the unit.

• Disengage the PTO. Shut off the engine and wait for

all moving parts to stop before attaching, adjusting,
or disconnecting any part of the collection system.

• Check the collection system to make sure it is bolted

tightly to the unit.

• DO NOT operate the unit without either the entire

grass catcher or the deflector in place.

• Turn off the PTO to disengage the blades when not

mowing.

• DO NOT mow in reverse unless absolutely neces-

sary. Always look down and behind before and while
travelling in reverse.

• DO NOT turn sharply when travelling alongside a

building or any object. Slow down before turning.

• DO NOT carry passengers.
• When collection system is removed from the mower

deck, the deflector must be properly installed.

• Collector bags are subject to deterioration and wear

during normal use.  Inspect the bag periodically for
tears, holes, or weak spots and replace with a new
bag that meets manufacturer’s durability standards.

• If the mower stalls or the collector chute plugs: 

1. Disengage the PTO;
2. Stop the engine and remove the key;
3. Set the parking brake, and wait for all moving
parts to stop.
4. Remove the foreign object or clear the chute
with a piece of wood before restarting the engine.
NEVER place hands into COLLECTOR OR
MOWER housing to clear jammed objects.
Blower OR MOWER may rotate when object is
removed.

• For added stability and to prevent tipping or loss of

control:

a. Use reduced speed on uneven ground and
when turning corners.
b. Reduce loads on hillsides. It is recommended
that the collection system be kept only half full
when negotiating any slopes. Start mowing on
slopes when the collection system is empty.
c. Mow up and down the face of slopes; never
across the face of any slope.

• Never operate on slopes greater than 17.6%

(10°). 

GENERAL WARNINGS

TP 600-2562-01-AT-SMA

Attachment Decal

These labels are easily applied and will act as a constant
visual reminder to you, and others who may use the
equipment, to follow the safety instructions necessary for
safe, effective operation.

Thrown objects hazard

• Objects thrown by the mower can seriously 
   injure or kill you.

• Do not open the hopper while the mower blades 
   are turning.

• Do not operate the mower without the complete 
   catcher in place. 

WARNING

1732819

Decal - WARNING
Thrown Objects Hazard
Part Number 1732819

Read and obey all operation and warning decals.

Содержание 1695169















Отзывы: