background image

TO OBTAIN WARRANTY SERVICE:

If you have any questions regarding this warranty or if your equipment requires a
covered repair, please contact us at the address below.

ALLTRADE TOOLS, LLC.

1431 VIA PLATA

LONG BEACH, CA 90810-1462 USA

CALIFORNIA EVAPORATIVE EMISSION CONTROL WARRANTY STATEMENT 
YOUR WARRANTY RIGHTS AND OBLIGATIONS

The California Air Resources Board and Alltrade Tools, LLC are pleased to explain
the evaporative emission control system's warranty on your 2009 generator. In
California, new equipment that use small off-road engines must be designed, built,
and equipped to meet the State's stringent anti-smog standards. Alltrade must war-
rant the evaporative emission control system on your generator for the period list-
ed below provided there has been no abuse, neglect or improper maintenance of
your equipment.

Your evaporative emission control system may include parts such as: carburetors,
fuel tanks, fuel lines, fuel caps, valves, canisters, filters, vapor hoses, clamps, con-
nectors, and other associated components. 

MANUFACTURER'S WARRANTY COVERAGE

This evaporative emission control system is warranted for two years. If any evapo-
rative emission-related part on your equipment is defective, the part will be repaired
or replaced by Alltrade.

OWNER'S WARRANTY RESPONSIBILITIES

As the generator owner, you are responsible for the performance of the required
maintenance listed in your owner's manual. Alltrade recommends that you retain all
receipts covering maintenance on your generator, but Alltrade cannot deny warran-
ty solely for lack of receipts.

As the generator owner, you should however be aware that Alltrade may deny you
warranty coverage if your generator or any part of the generator has failed due to
abuse, neglect, or improper maintenance or unapproved modifications.

You are responsible for presenting your generator to an authorized Alltrade Service
Center as soon as a problem occurs. The warranty repairs should be completed in
a reasonable amount of time, not to exceed 30 days. If you have any questions
regarding your warranty, rights or responsibilities, please contact Alltrade Customer
Service at 1-888-278-8092.

40

G. Throughout the ECS Warranty Period, Alltrade shall maintain a supply of warrant-

ed emission-related parts sufficient to meet the expected demand for such parts.

H. Any Alltrade authorized and approved emission-related replacement parts may

be used in the performance of any ECS warranty maintenance or repairs and will
be provided without charge to the purchaser/owner. Such use shall not reduce
Alltrade ECS Warranty obligations.

I. Unapproved, add-on, modified and/or counterfeit parts may not be used to modi-

fy or repair an Alltrade engine. Such use voids this ECS Warranty and shall be suf-
ficient grounds for disallowing an ECS Warranty claim. Alltrade shall not be held
liable hereunder for failures of any warranted parts of Alltrade equipment caused
by the use of such an unapproved, add-on, modified and/or counterfeit part.

EMISSION RELATED PARTS MAY INCLUDE THE FOLLOWING (IF INCLUDED ON
THIS ENGINE):

1. Fuel Metering System

a. Carburetor and internal parts

b. Fuel Regulator

2. Air Induction System

a. Intake manifold

b. Air filter

3. Ignition System

a. Spark plugs

b. Magneto ignition system

4. Air Injection System

a. Air cleaner

5. Exhaust System

a. Catalyst

b. Exhaust Manifold

6. Miscellaneous Items

a. Fittings, tubing, connectors and assemblies. 

39

Содержание SR3000






















Отзывы: