background image

INTRODUCTION ........................................................................... 1
CONTENTS ................................................................................... 1
SPECIFICATIONS ......................................................................... 2
INSTALLATION ............................................................................. 2
OPERATION ................................................................................. 4
SCHEMATIC DIAGRAM ................................................................ 4
PARTS BREAKDOWN.................................................................. 5

MANUFACTURER’S LIMITED WARRANTY

This equipment is warranted against defects in materi-

als and workmanship for a period of 

90 DAYS

 from the date

of purchase.

Should it become defective for such reason, the Manu-

facturer will repair it without charge, if it is returned to the
Manufacturer’s factory, freight prepaid.  This warranty
does not cover:  (1) failure due to normal wear and tear;  (2)
consumable parts, such as, but not limited to, collets, collet
bodies, gas cups and heat shields;  (3) damage by acci-
dent, force majeure, improper use, neglect, unauthorized
repair or alteration;  (4) anyone other than the original
purchaser.

THIS LIMITED WARRANTY IS IN LIEU OF ALL

OTHER WARRANTIES, EXPRESS OR IMPLIED.  THE
MANUFACTURER SHALL NOT BE LIABLE FOR ANY
INJURY TO PERSONS, INCLUDING DEATH; OR LOSS
OR DAMAGE TO ANY PROPERTY, DIRECT OR CON-
SEQUENTIAL, INCLUDING, BUT NOT LIMITED TO,
LOSS OF USE, ARISING OUT OF THE USE, OR THE
INABILITY TO USE, THE PRODUCT.  THE USER AS-
SUMES ALL RISK AND LIABILITY WHATSOEVER IN
CONNECTION WITH THE USE OF THE PRODUCT,
AND BEFORE DOING SO, SHALL DETERMINE ITS
SUITABILITY FOR HIS INTENDED USE, AND SHALL
ASCERTAIN THE PROPER METHOD OF USING IT.

SOME STATES DO NOT ALLOW LIMITATIONS ON

HOW LONG AN IMPLIED WARRANTY LASTS, OR THE
EXCLUSIONS OR LIMITATIONS OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES.  SO THE ABOVE LIMI-
TATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS, AND YOU MAY HAVE OTHER RIGHTS WHICH
MAY VARY FROM STATE TO STATE.

TABLE OF CONTENTS

Snap-on Tools Corporation  Kenosha, WI  53141-1410

Содержание FLEX-TIG









Отзывы: