SMP ZINGO DU X-002/P, Руководство по установке

Страница: 58 / 60

ZINGO DU X-002
Appendix C Page 58
ii) Shim under legs of frames ensuring that they are plumb and square and orientated correctly with the
welded F.S.L. mark at the correct level.
NOTE: See “Appendix A STEP 17” for assembly of Plastic Slide and relevent components.
44) Assemble Slide Feet (items 19 & 20) to underside of Slide (item 18) and secure using 2 off M10 x 16 Hex.
Bolt (item 56) and Heavy Duty Washers (item 57). STEP 17
45) Offer Slide (item 18) up to Entry Frame (item 10) ensuring the top of the slide rests on the cross member. The
walls of the slide must be positioned outside of the gussets on the entry frame.
i) Shim under the slide legs to set the slide plumb and square adjust the slide exit to the required height.
STEP 17
ii) Secure the slide to the gussets using 2 off M6 x 10 Resistorx bolts (item 55) and M6 Nyloc nuts
(item 60). The Resistorx bolts heads must be on the inside of the slide.
STEP 17
NOTE: The slide runout should taper towards the ground at a angle of 1.5° max. to allow a watershed.
NOTE: It is very important to check the slide run out section does not hold water after installation. It is
recommended that an actual test be carried out, on site, prior to concreting the slide into its final position.
Should any deformation to the run out section have occurred during transportation and storage this must be
corrected prior to final installation.
46) Assemble Seat Mounting Frame (item 9) to Clamp Rings (half) (item 47) at 300 Deck Clamp Height as shown.
Each end of the frame is held between a Bar Socket Top (item 49) and a Bar Socket Bottom (item 48) using
1/4” unc x 5/8” BHCS Fixings (item 72).
STEP 18
i) For assembly method see Note 4.1, 3), i) to v).
ii) Shim under leg of frame ensuring that it is plumb and square and orientated correctly with the welded
F.S.L. mark at the correct level.
NOTE: Note the short arm on the top of the Seat Mounting Frame is positioned towards the outside of the main
structure.
47) Assemble Rope Net Mounting Bracket (item 16) to lower deck mounting face using 3 off M10 x 30 Resistorx
bolts (item 53) and Washers (item 58). STEP 19
48) Attach in 2 places 1 off Climb Rope Tether (item 17) to the Clamp Rings (half) that are 900mm Deck Clamp
Height and 300mm Deck Clamp Height on Curved Leg - 900 Deck (item 2). Each Climb Rope Tether is held
between a Bar Socket Top (item 48) and a Bar Socket Bottom (item 47) using 2 off BHCS Fixings (item 66)
and should be orientated correctly to the leg.
STEP 19
i) For assembly method see Note 4.1, 3), i) to v).
49) Place 1 off Rope Support Leg (item 4) into its foundation hole. Shim as required to align rope fixings with
appropriate fixings on leg and check position and orientation. Ensure the post is plumb and square, using
suitable props to hold leg safely in position.
STEP 19
50) Mark out the ground fixing position for the Ground Fixing Chain Assemblies (item 41) in 2 positions in the base
of the appropriate foundaion holes for the fixing of the Climbing Net (item 36). STEP 20A
NOTE: For Loose Fill positions see STEP 20B
51) Suspend the Ground Fixing Chain Assembles vertically above the previously marked positions, ensuring that
at least 13 chain links are encased in the concrete to provide a secure fixing, with the Hex. bolt at the bottom
of the hole.
STEP 20
52) Mark out the ground fixing position for the Ground Fixing Chain Assemblies (item 41) in 4 positions in the base
of the appropriate foundaion holes underneath the posts. STEP 21
53) Suspend the Ground Fixing Chain Assembles vertically above the previously marked positions, ensuring that
at least 13 chain links are encased in the concrete to provide a secure fixing, with the Hex. bolt at the bottom
of the hole.
STEP 21
NOTE: Check that the completed structure has been positioned in the correct place, that it is plumb and
square and all the fasteners are fully tightened to the correct torque settings. Also ensure that the
structure is propped safely so that it may be left for the concrete foundations to cure.
ISSUE L 15-11-2010