Smithy Midas 1220 XL Скачать руководство пользователя

Страница: 66 / 115

Figure 12.4 With a file, take full strokes at an oblique angle and never hold the file still.

For an even finer file finish, rub railroad chalk into its teeth. This provides additional

lubrication and absorbs filings. Do not use blackboard chalk.

After filing off the machining marks, polish the workpiece with emery or other abrasive

cloth. Keep the lathe turning at high speed and spread a few drops of oil on the

workpiece. Don’t stop moving the cloth (Figure 12.5).

Figure 12.5 You can polish a workpiece with an abrasive cloth and oil.

Taper Turning

There are two ways to turn a taper: with the compound rest and by setting over the

tailstock. In both methods, the cutter must engage the work on dead center if the taper

is to be accurate.

Compound Rest. Tapers cut with the compound rest are usually short, abrupt angles,

such as centers, bevel gear blanks, and die parts (Figure 12.6). In general, these are not

considered taper turning, which applies to machining longer, more gradual tapers.

Setting over the tailstock. Cuttting tapers by setting over the lathe tailstock involves

misaligning the lathe centers. The lathe centers move from their position parallel to the

tool’s transverse travel, giving the desired degree of taper (Figure12.7) The tailstock has

a set-over scale calibrated both forward and backward from the straight turning or

zeroing point for measuring set-over distances.

12-4

For Assistance: Call Toll Free 1-800-476-4849

Midas 1220 XL Operator’s Manual

Содержание Midas 1220 XL




















































































































Результаты поиска

Содержание Midas 1220 XL

Отзывы:

Похожие инструкции для Midas 1220 XL

Бренды по названию

Популярные бренды

Smithy Midas 1220 XL, Руководство оператора

Результаты поиска

Содержание Midas 1220 XL

Отзывы:

Похожие инструкции для Midas 1220 XL

Бренды по названию

Популярные бренды