manualshive.com logo in svg

Smithco TCV 2200 32-000, Запасные части и руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Smithco TCV 2200 32-000 Скачать руководство пользователя страница 7

5

Introduction

A. Oil Light - The oil light should come on when the ignition is on without the

engine running and go out when the engine is running. The oil light will
light when the oil pressure is low. If oil light should come on, shut engine
off immediately and find the cause.

B. Ignition Switch - The ignition switch has three positions: Off - Run - Start.

C. Tilt Steering - Hold lever down and adjust steering wheel to desired

position and release lever.

D. Lights - This rocker switch turns lights on by pushing on the top and off

by pushing on the bottom.

E. Hand Throttle -  The hand throttle is used to regulate engine speed.

F. Cup Holder - Holds 2 large cups.

G. Park Brake - The park brake is only a parking brake. Pull back to release,

push forward to apply.

H. Dump Box Lever - The dump box lift lever is used to raise and lower the

dump box.  Pull back to raise the dump box. Push forward to lower the
dump box.

I. Choke - The choke is used in starting the engine. Pull choke out to close

choke plate when starting a cold engine. Push in when engine starts. A
warm engine may not require "choking" to start.

J. Brake Pedal -  Operates the hydraulic brakes on the front axle.

K. Forward Pedal - This pedal controls ground speed. Varying  the amount of

movement of the pedal will vary the ground speed.

L. Reverse Pedal - This pedal controls reverse ground speed.

M. Hour Meter - The hour meter indicates hours of machine operation. It operates only when the ignition

switch is on. Located on left ROP's mount.

CONTROLS & INSTRUMENTS

Содержание TCV 2200 32-000























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды