Smith FS300 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 22

background image

SMITH Manufacturing 1-954-941-9744 www.SmithMfg.com

SMITH Manufacturing 1-954-941-9744 www.SmithMfg.com

VERSION 8/2013

FS300

Gas

HANDLE BAR ADJUSTMENT

The handlebars are equipped with a high-density

vibration suppression material to minimize

operator fatigue and increase comfort level when

operating equipment. To adjust the handlebars

to a new position for different height operators

please follow these steps:

•

Using a wrench or socket (13mm), loosen

the bolts on both sides of the handlebars

two to three turns only.

•

Adjust handlebar to desired position and

re-tighten the 4 screws

Never operate with handlebars loose.

The bolts must be fastened tightly assuring

the handle is locked into position.

Loosen to

adjust

5

«
...
3
4
5
6
7
...
»

Содержание FS300























Отзывы:

Нет отзывов

Похожие инструкции для FS300

Бренд: Baby Lock Страницы: 56

Бренд: Baroness Страницы: 28

Бренд: Quasar Страницы: 124

Бренд: Singer Страницы: 67

Бренд: Numatic Страницы: 16

Бренд: JUKI Страницы: 4

Бренд: Chandler Страницы: 27

Бренд: Chandler Страницы: 50

Бренд: Ice Страницы: 47

Бренд: Ice Страницы: 46

Бренд: Trusted Clean Страницы: 15

Бренд: Rexel Страницы: 44

Бренд: American-Lincoln Страницы: 57

Бренд: Palamides Страницы: 62

Бренд: Protect Страницы: 28

Бренд: Husqvarna Viking Страницы: 36

Бренд: Husqvarna Viking Страницы: 44

Бренд: Pfaff Страницы: 73

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды