Smith FS300 Скачать руководство пользователя страница 2

Страница: 2 / 22

SMITH Manufacturing 1-954-941-9744 www.SmithMfg.com

FS300

VERSION 8/2013

Gas

SMITH Manufacturing 1-954-941-9744 www.SmithMfg.com

INTRODUCTION

Congratulations

on purchasing the

FS300™ heavy duty remover from

SMITH Mfg. Company.

Your machine will:

• Clean surfaces impacted by grease, oil,

plastics, tars, resins, tile adhesives, ice and

• Plane or mill asphalt and concrete surfaces

• Remove high spots in curbs and gutters

• Eliminate trip-hazards on concrete sidewalks

• Mill areas for rumble strips

• Clean out cracks and joints

• Create anti-slip patterns in walkways and barns

• Prepare surfaces for new coating applications

• Permanently remove all road and surface

coatings to include:

epoxy, urethane, thermoplastic, paint,

glue-backed tapes and more...

• Groove-inlay asphalt for striping

BEFORE START-UP,

READ THIS..

Please read all operating instructions, including

the provided motor manual and be completely

familiar with your equipment before operating.

When in doubt, please contact SMITH

Manufacturing Customer Service for operational

details. This Owner’s Manual will guide you

through the removal process, from start to finish,

and show you how to care for your machine.

Page Contents

Index / Introduction

Safety Guidelines

Your FS300 Surface Preparator

Handle Adjustment Instructions

Machine Start-Up

Substrate Removal

Storage, Ordering, and Warranty Claims

Troubleshooting

Maintenance Check List

11-12

General maintenance

13-14

Bearing replacement

15-17

Optional Equipment

18-19

Maintenance Log

Limited Equipment Warranty

Warranty Activation

INDEX

Содержание FS300























Результаты поиска

Содержание FS300

Отзывы:

Похожие инструкции для FS300

Бренды по названию

Популярные бренды

Smith FS300, Руководство пользователя

Результаты поиска

Содержание FS300

Отзывы:

Похожие инструкции для FS300

Бренды по названию

Популярные бренды