background image

49

Instructions for the installer

8.7

 Electrical connection

Make sure that the voltage and capacity of the power line conform to the data shown on the plate
located under the casing. 

Do not remove this plate for any reason.

 

THE HOB MUST BE CONNECTED TO THE POWER SUPPLY BY A QUALIFIED TECHNICIAN.

BEFORE ANY INTERVENTION, DISCONNECT THE POWER SUPPLY OF THE HOB.

THE APPLIANCE MUST BE CONNECTED TO EARTH IN COMPLIANCE WITH ELECTRICAL
SYSTEM SAFETY REGULATIONS.

WHEN LINKING UP TO THE POWER SUPPLY NETWORK BY PLUG AND SOCKET, MAKE SURE
THAT BOTH ARE COMPATIBLE AND THEY SHOULD BE CONNECTED BY MEANS OF A POWER
CABLE COMPLYING WITH THE REGULATIONS IN FORCE.   THE SOCKET MUST BE ACCESSIBLE
AFTER THE APPLIANCE HAS BEEN BUILT IN. 

NEVER UNPLUG BY PULLING ON THE CABLE

.

IMMEDIATELY AFTER INSTALLATION CARRY OUT A BRIEF INSPECTION TEST OF THE HOB,
FOLLOWING THE INSTRUCTIONS. IF THE HOB FAILS TO OPERATE, AFTER CHECKING THAT
YOU HAVE CARRIED OUT THE INSTRUCTIONS CORRECTLY, DISCONNECT THE APPLIANCE
FROM THE ELECTRICAL MAINS AND CONTACT YOUR NEAREST SERVICE CENTRE. 

NEVER ATTEMPT TO REPAIR THE APPLIANCE.

RUN THE POWER CABLE UNDER THE UNIT, TAKING CARE THAT IT DOES NOT COME INTO
CONTACT WITH THE BOTTOM OF THE CASING OF THE HOB OR THE OVEN BENEATH IT IF
THERE IS ONE. 

THE EARTHING WIRE MUST BE LONGER THAN THE CONDUCTING WIRES SO THAT, IF THE
PLUG IS TORN OFF THE POWER CABLE, IT IS THE LAST TO BE DETACHED.

AVOID USE OF ADAPTERS AND SHUNTS AS THESE COULD CAUSE OVERHEATING AND RISK
OF BURNS.

WHERE A FIXED CONNECTION IS IN USE, A MULTIPOLAR CUT-OUT DEVICE MUST BE
INSTALLED ON THE SUPPLY CABLE WITH A CONTACT OPENING DISTANCE EQUAL OR
GREATER THAN 

3 MM

, LOCATED IN A READILY REACHABLE POSITION NEAR THE APPLIANCE.

The manufacturer declines all responsibility 

for damage to persons or things caused by non-

observance of the above prescriptions or by tampering with any part of the appliance.

The adjacent diagram illustrates the power supply terminal
from below, with no cables connected. Terminals 4 and 5
must be connected at all times.

1 2 3 4

L1 L2

N N

5

Содержание SI3842B

























Отзывы: