background image

 

 

Instructions for the installer 

 

11 

3.

 

GAS CONNECTION 

 

This  appliance  is  suitable  for  installation  with  Natural 

Gas  or  ULPG  (propane).  Refer  to  page  12  for  the 

relevant  burner  pressure  and  appropriate  injector 

sizes.  When  the  appliance  is  to  be  connected  to 

Natural Gas then the pressure regulator supplied must 

be fitted to the gas inlet. A test point (for checking the 

gas pressure) is supplied either with the regulator or as 

a  separate  fitting  in  the  case  of  LPG  (propane) 

appliances. 

Connection of the appliance to the gas supply must be 

in accordance with the requirements of AS5601. A ½” 

BSP  connector  at  the  inlet  is  recommended  and  the 

gas supply line to the appliance must be of adequate 

length  to  allow  sufficient  withdrawal  of  appliance  for 

service or disconnection and be: 

1.

 

annealed copper pipe or; 

2.

 

flexible  hose  according  to  AS/NZ1869  &  be  at 

least Class “B”, 10 mm diameter. 

 

The  appliance  must  be  installed  with  provision  to  allow  the  gas  to  be 

turned off and disconnected for servicing and removal of the appliance 

as required from the gas supply. 

Before  the  appliance  is  operated  make  certain  all  relevant  parts  are 

placed in the correct position. 

When  the  installation  is  completed  the  installation  connections  of 

appliance  will  require  to  be  leak  tested,  the  burner  operating  pressure 

and flame checked and adjusted. 

Warranty service calls do not cover these adjustments! 

To check the operating pressure of the appliance it is recommended at 

least 2 large size burners are used. Ensure appliance is secured to wall 

when installation is completed. 

N.G. The regulator supplied  must be fitted  to the ½ BSP thread  at the 

rear  of  the  appliance.  An  approved  manual  shut-off  valve  must  be 

installed.  The  N.G.  regulator  must  be  checked  and  adjusted  to  1.0kPa 

after installation. 

 

U.L.P.G.

Can  be  connected  to  the  inlet 

fitting  directly.  The  pressure  must  be 

checked  to  ensure  it  is  operating  at 

2.75kPa. A separate test point fitting must 

be  installed  between  the  piping  &  the 

appliance  for  the  pressure  to  be  checked 

to ensure it is operating at 2.75kPa. 

 

 

 

Содержание PV631CNXAU





















Отзывы: