background image

Use

13

EN

3.2 First use

1. Remove any protective film from the 

outside or inside of the appliance, 
including accessories.

2. Remove any labels (apart from the 

technical data plate) from accessories.

3. Remove and wash all the appliance's 

accessories (see 4 Cleaning and 
maintenance).

3.3 Using the cooktop

All the appliance’s control and monitoring 
devices are located together on the front 
panel. The burner controlled by each knob 
is shown next to the knob. The appliance is 
equipped with an electronic ignition device. 
Simply press the knob and turn it anti-
clockwise to the maximum flame symbol, 
until the burner ignites. If the burner does not 
light in the first 15 seconds, turn the knob 
to 

 and wait 60 seconds before trying 

again. After lighting, keep the knob pressed 
in for a few seconds to allow the 
thermocouple to heat up. The burner may 
go out when the knob is released: In this 
case, the thermocouple has not heated up 
sufficiently. Wait a few moments and repeat 
the operation. Keep the knob pressed in 
longer.

Correct positioning of the flame-
spreader crowns and burner caps

Before lighting the cooktop burners, make 
sure that the notches of the flame-spreader 
crowns (

A

) are positioned in their 

corresponding housings (

B

) with their 

respective burner caps. Make sure that the 
holes in the burner (

C

) are aligned with the 

igniters and thermocouples (

D

). Also ensure 

that the flame-spreader crowns are 
correctly engaged in the burner holes.

In case of an accidental switching 
off, a safety device will be tripped, 
cutting off the gas supply, even if 
the gas tap is open. Return the 
knob to 

 and wait at least 

60 seconds before lighting it 
again.

Содержание Linea PX7502AU





























Отзывы: