background image

7

7

a) Water inlet hose 

The specific hoses that come with the 

machine are connected to the water inlet 

valves on the machine. Red labeled hose 

is for hot water inlet and blue labeled hose 

is for cold water inlet.

In order to prevent the water leakages that 

may occur on the connection points, rub-

ber seals are placed on the hose or in the 

package (4 pieces for the models with 

double water inlets and 2 pieces for other 

models). These gaskets should be used 

for connections in both sides of the hose. 

Gaskets on the machine side should fit in 

the hose filter channel.

Since the connection points are under 

water pressure, turn on the taps to the 

maximum after the connection. Check if 

there is any water leakage at the connec-

tion points. In order to prevent the water 

leakages and the damages they may 

cause, keep the taps closed when you are 

not using the machine.

Minimum 1 bar and maximum 10 bars of 

water flow from the tap is enough for your 

machine to operate efficiently. (In practice, 

1 bar means that more than 8 liters of wa-

ter per minute flows from a full open tap.)

Install the elbowed end of the hose to your 

machine. Hand-tighten the nuts of the 

hose, do not use a spanner

Models with double water inlets can be 

used as a model with a single water inlet 

by using a plug. Plug should be installed to 

the hot water valve. A rubber gasket should 

be used in order to prevent water leakage 

from the connection point.

Do not connect the product with single wa-

ter inlet to the hot water tap. The product 

may switch to the protection mode if the 

temperature of the water connected to a 

product with double water inlet through a Y 

part and single water inlet is above 40°C. 

a) Water drainage hose 

Water drainage hose can be attached to 

the side wall of a sink or bathtub. Hose 

should not be bend. When the drainage 

hose is hanged on a sink or bathtub, it can 

be secured with a hose bracket so that it 

will not fall.

The end of drainage hose can be 

connected directly to the waste water 

drainage hole or to the specific end that is 

installed to the outlet elbow of the sink.

 The hose should be installed to a height 

of 40 cm minimum and 100 cm maximum.

Water connections

Содержание LBS 845















Отзывы: